manualshive.com logo in svg

SMC Networks EX260-VIL1, Руководство по эксплуатации, Страница: 13 / 41

Поделиться
Скачать
SMC Networks EX260-VIL1 Скачать руководство пользователя страница 13

-

13- 

 

No.EX

※※

-

OMZ0018

 

 

 

 

3.2.1. 

MinCycleTime, ProcessDataIn/Out, Device ID

 

 

Table 3-3. MinCycleTime, ProcessDataIn/Out, Device ID 

Vacuum manifold 

stations 

MinCycleTime 

(Address : 0x02) 

ProcessDataIn 

(Adress : 0x05) 

ProcessDataOut 

(Adress : 0x06) 

Device ID 

(Adress : 0x09...0x0B) 

4 

0x28 (4.0 ms) 

0x83 (4 byte) 

0x10 (2 byte) 

0x000254 

8 

0x2E (4.6 ms) 

0x84 (5 byte) 

0x82 (3 byte) 

0x000255 

12 

0x34 (5.2 ms) 

0x85 (6 byte) 

0x83 (4 byte) 

0x000256 

16 

0x3A (5.8 ms) 

0x86 (7 byte) 

0x84 (5 byte) 

0x000257 

 

3.3. 

IO-Link defined parameters 

 

Table 3-4. IO-Link defined parameters 

Index(dec) 

Parameter 

Access 

Value/Description/Remark 

0x0002(2)  SystemCommand 

W 

Refer to 

Section 3.3.1

. 

0x0003(3)  DataStorageIndex 

R/W 

--- 

0x0010(16)  VendorName 

R 

SMC Corporation 

0x0011(17)  VendorText 

R 

www.smcworld.com

 

0x0012(18)  ProductName 

R 

Vacuum manifold 4 stations    : EX260-VIL1_4_ejectors 
Vacuum manifold 8 stations    : EX260-VIL1_8_ejectors 
Vacuum manifold 12 stations : EX260-VIL1_12_ejectors 
Vacuum manifold 16 stations : EX260-VIL1_16_ejectors 

0x0013(19)  ProductID 

R 

EX260-VIL1 

0x0014(20)  ProductText 

R 

Vacuum Manifold 

0x0015(21)  SerialNumber 

R 

**...*(16 characters max.) 

0x0016(22)  HardwareRevision 

R 

V*.* 

0x0017(23)  FirmwareRevision 

R 

V*.*.* 

0x0018(24)  ApplicationSpecificTag 

R/W 

Default value : **...*(32 characters)   
Can be set to 16-32 characters. 

0x0024(36)  DeviceStatus 

R 

Refer to 

Section 3.3.2

. 

0x0025(37)  DetailedDeviceStatus 

R 

Refer to 

Section 3.3.3

. 

 

3.3.1. 

SystemCommand (Index 2) 

 
The various reset commands supported by the SI Unit are as follows. 
 

Table 3-5. SystemCommand 

Value 

Command 

Description/Remark 

0x80  Device reset 

The SI Unit restarts with the power on. 

0x81  Application reset 

Reset vendor defined parameter to default values while maintaining IO-Link 
communication. 

0x83  Back-to-box 

Reset vendor defined parameter to default values and disable IO-Link 
communication. 
IO-Link communications can be restored by restarting the SI Unit. 

Содержание EX260-VIL1










































Отзывы:

Нет отзывов