background image

-22- 

 

No.EX

※※

-OMV0023 

 

 

Troubleshooting table 

Fault No.1 

Fault 

Probable cause 

Recommended error handling 

Recommended action 

SI unit 
ST LED is 
OFF 

Defective power 
cable wiring for SI 
unit operation 

Check the condition of the power cable 
wiring to the SI unit. 

Re-tighten the power cable. 
(Replace the cable if it is broken) 

Correct the power cable wiring 
layout. 

SI unit operating 
voltage is not 
supplied 

Check the condition of the supply voltage to 
the SI unit. 

Supply 24 VDC 

10% to the SI 

unit. 

SI unit ST 
LED is OFF 
and S/E LED 
is red ON 

Node ID number is 
outside range. 

Check the Node ID setting. 

Set the Node ID number from 1 
to 239. 

 
Fault No.2

 

Fault 

Probable cause 

Recommended error handling 

Recommended action 

SI unit 
PWR (V) 
LED is OFF 

Defective power 
cable wiring for the 
solenoid valve 

Check the condition of the power cable 
wiring for the valve. 

Re-tighten the power cable. 
(Replace the cable if it is broken) 

Correct the power cable wiring 
layout. 

Load voltage for the 
valve is not 
supplied 

Check the condition of the supply voltage 
for the valve. 

Supply 24 VDC +10%/-5% to 
the valves. 

 
Fault No.3 

Fault 

Probable cause 

Recommended error handling 

Recommended action 

SI unit L/A 
LED is OFF 

POWERLINK 
communication 
error between the 
SI unit and the 
upstream 
POWERLINK 
device. 

Check the condition of the upstream 
POWERLINK device. 

Supply power to the upstream 
POWERLINK device. 

Check the BUS IN side communication 
cable connections and check for broken 
wires.

 

Tighten the communication 
cable connection. 
(Replace the cable if it is broken)

 

Check that there are no high voltage cables 
or equipment that generates noise around 
the communication cable and SI unit.

 

Take measures to keep the 
communication cable and SI unit 
away from noise sources.

 

 
Fault No. 4 

Fault 

Possible cause 

Investigation method 

Countermeasures 

SI unit 
ST LED is red 
ON 

Failure of SI unit. 

Replace the SI unit and check that it 
operates normally. 

Replace the SI unit. 

Содержание EX260-SPL1



































Отзывы: