Smawave Technology SGL4010 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 54

background image

1 Getting Started

1.1Welcome to the CPE

In this document, the LTE (Long Term Evolution) CPE (customer premises equipment) will be
replaced by the CPE. The CPE support B2/4/5/8/12/13/14/25/26/66/38/41/42/43/48/53.

And its tx power is 23

±

2.

Carefully read the following safety symbols to help you use your CPE safely and correctly:

Additional information

Optional methods or shortcuts for an action

Potential problems or conventions that need to be specified

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

—Consult the dealer or an experienced radio/TV technician for help.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

The customer does not have permission to modify the parameters of the device.

The device usage scenario is 20cm away from the human body.

«
...
2
3
4
5
6
...
»

Содержание SGL4010























































Отзывы:

Нет отзывов

Похожие инструкции для SGL4010

Бренд: Ubiquiti Страницы: 24

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Бренд: 4RF Страницы: 7

Бренд: Maxim Страницы: 14

Duinotech Lilypad Plus XC3920

Бренд: Jaycar Electronics Страницы: 2

Бренд: H3C Страницы: 9

Бренд: Supero Страницы: 16

Бренд: Federal Signal Corporation Страницы: 49

Бренд: TP-Link Страницы: 16

Бренд: CAME Страницы: 32

Бренд: uneron Страницы: 13

MP5S Plus Writer

Бренд: SONIX Страницы: 23

Бренд: Mobily Страницы: 12

Бренд: Homeworks Страницы: 24

Бренд: LevelOne Страницы: 2

Бренд: Toto Link Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды