background image

 

 

FOUNDATION 

SMART STORE WOODEN FLOOR  

 

 

The optional Smart Store kitset wooden floor is precut and de-
signed to be fitted into the shed after the shed is assembled. 

  

 

Assemble shed as per  instructions and fit floor last. 

          (see page 13 for details).  

CONCRETE SLAB FOR RAISED BASE PLATE SHED 

 

To build a raised concrete slab for your shed to sit on, we recom-

mend the following: 

 

 

The raised slab size should be 15mm smaller than the base 
size of the shed and at least 30mm above ground line. 

 

 

The slab should be 80mm thick in the middle and 100mm 
thick around the edges. 

 

 

The slab should be laid on a solid or compacted base. 

 

 

Plastic sheeting under slab will prevent moisture coming 
through from underneath

.

 

 

 

During construction, you may raise the  bottom timber 
plate to allow the wall cladding to protrude 20mm below 
the bottom plate. This will stop water flowing between 
the bottom plate and the concrete floor.  

          

See note on page 7.

 

80mm 

100mm 

7.5mm

 

20mm

 

Concrete Floor

 

Base Plate

 

Wall Cladding

 

RAISED BASE PLATE OPTION 

(For sheds placed on a raised concrete floor) 

No doubt by now you will have decided what sort of base you are putting down.  

Please read the section that applies to your situation. 

If you choose to pour a concrete base you will need to decide whether you wish to raise the base plate of your shed. 

This allows the cladding to protrude below the surface of the concrete  and ensures a  water tight pad.  

See concrete pad specifications below 

By choosing this option you will need to make the pad to the specification below. 

Содержание SS2020

















Отзывы: