background image

 

 

ASSEMBLE

 

SIDE PANELS

 

8

 

SELECT:

 

 

4 x 1.920 m Gable Wall Sheets (Angled)

 

4 x 1.980 m Gable Wall Sheets (Angled)

 

2 x 2.020 m Top Plates (Red)

 

2 x 2.020 m Bottom Plates (Green)

 

96 x 30mm Galv Clouts

 

12 x Rivets

 

 

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER 

BASE PLATE –READ THE FOLLOWING;

 

 

For sheds with Raised Base Plate option only (see page 6), deduct 

30mm from measurement shown between Top and Bottom Plates on 
all wall panels, so cladding protrudes 20mm below bottom plate

.

 

Ie. reduce 1850mm to 1820mm between Plates.

 

STEP 1:

 

 

• 

Lay out 1 x Top plate and 1 x  Bottom plate on a flat surface as shown 
(corner cut

-

outs to face outwards). 

Measurements between Top and 

Bottom plates are critical to ensure wall panels fit together.

 

STEP 2:

 

 

• 

Place 2 x 1.920 m wall sheets and 2 x 1.980 m wall sheets on top 
of timber plates with bottom of sheets flush with each other.

 

• 

Rivet sheets together on overlaps as shown

.

 

STEP 3:

 

 

• 

Nail wall sheets to the Top Plate at each end making 
sure that the top corners of the sheets are flush with 
the top of the Top Plate and that the sides of the wall 
sheet overhang the Top Plate by approx 15mm as 
shown.

 

 

• 

Check that the Top Plate is straight then nail the 

 

      Wall sheet to the Top Plate, 2 clouts per pan. 

 

     (see 

fig. 1

).

 

Standard Shed —

 

Bottom Plate will protrude be-

low wall sheet by approximately 10mm. 

 

 

Raised base plate shed —

 

Wall sheet will protrude 

 

below the Bottom Plate by 20mm

.

 

 

STEP 4:

 

 

• 

Nail the wall sheets to the Bottom Plate at each end ensuring each side 
of wall sheets overhangs the end of Bottom Plate by 15mm. Check that 
the distance between the Top and Bottom Plates is correct. (As per 
diagram in step 1)

 

 

• 

Check that the Bottom Plate is straight then nail the wall sheets to the 
Bottom Plate, two clouts per pan (see fig. 1).

 

fig.1

 

RIB

 

PAN

 

CLOUT

 

TIMBER PLATE

 

TOP PLATE

 

BOTTOM PLATE

 

RIVET

 

RIVET

 

RIVET

 

RIVET

 

RIVET

 

RIVET

 

TOP PLATE

 

15mm

 

15mm

 

BOTTOM PLATE

 

1853mm

 

1853mm

 

TOP PLATE

 

BOTTOM PLATE

 

15mm

 

15mm

 

1853mm

 

TOP PLATE

 

1853mm

 

REPEAT  THESE STEPS TO MAKE SECOND SIDE WALL PANEL

 

15mm

 

Содержание SM3020

















Отзывы: