1. GETTING STARTED with SmartPro Finder I
Powering up
19
This tester can be powered by the use of batteries. Required AAA Batteries (x2), take note of
the positive (+) and negative (-) directions of batteries
(Fig 1.1).
The use of Alkaline batteries is
preferred, as it should generally give approximately 2.5 hours continuous operation, While the
use of ordinary batteries will give a shorter working life.
Press the [ON/OFF] button
(Fig. 1.3)
and wait for warm up the tester about 20 seconds.
10
12
14
The recommended testing temperature is 18
o
C - 27
o
C or 65
o
F - 80
o
F Please allow the gemstone or
jewelry piece to adjust to room temperature prior to testing. Exposure and/or operation of the tester
outside the room temperature would affect the result and performance of tester.
The probe tip must be placed at the right angle or perpendicular to the facet of gemstone for an
accurate reading.
Tests should be conducted on the table of the gemstone. In the event of any doubt, kindly test on
the girdle of the gemstones instead.
To achieve optimum accuracy for tests involving very small, it is important to allow the gemstone
to cool down before subsequent tests.
a. Keep the tester dry. Precipitation and all types of liquids or moisture can contain minerals that
will corrode electronic circuits. If your tester does get wet, remove the battery, and allow the
tester to dry completely before replacing it.
b. Do not use, store or expose the tester industry and dirty areas. It’s moving part and electronic
components can be damage.
c. Do not use, store or expose the tester in hot areas. High temperatures can damage or shorten
the life of the tester, damage batteries, and warp or melt certain plastics.
d. Do not use, store or expose the tester in cold areas. When the tester returns to its normal tem-
perature, moisture can form inside the device and damage electronic circuit boards.
e. Do not attempt to open the tester other than as instructed in user manual book.
III. IMPORTANT NOTICE
Fig. 1.1
Fig. 1.3
17
Fig. 1.5
While in this preparation mode, you can check status through the ORANGE “Ready” LED will blink
continuously until has the steady lighting with beep sound It’s means your tester is ready now for
use
(Fig.1.4)
.
15
Fig. 1.4
20
Fig. 1.2
9
11
13
Composition
1. Retractable probe tip
2. Serrated Metal Part
3 “Ready” Indicator LED
4. “Low Battery” Indicator LED
5. “Metal” Indicator LED
6. “Simulant” Indicator LEDs
7. “Diamond” Indicator LED
8. ON/OFF Button Switch
9. Battery compartment
10. Neck Strap Attachment
11. Probe Protective Cap
f. Do not drop, knock, or shake the tester. Rough handling can break internal circuit boards and
fine mechanics.
g. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the tester.
h. Do not paint the tester. Paint can clog the moving parts and prevent proper operation.
If the tester is not working properly, kindly contact our customer service at
SmartPro Instrument co.,ltd
249/40, Moo 9, J.S.P. Building
Bangbon 1 Rd., Bangbon
Bangkok 10150 Thailand
+66 (0) 2 899 2956-7
Attn: Customer Service Executive
Turning on
Remove the protective cover from the probe tip
(Fig. 1.2).
Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the
gemstone face down the table
(Fig.1.7).
Cleaning your gemstone prior to testing
Fig. 1.7
The gemstone should be clean and dry before testing. However, elaborate cleaning procedures
are not normally necessary
(Fig.1.6).
18
Recommended testing conditions
Fig. 1.6
Cleaning the probe tip
Please note that if the tester is being used for the first time, or if the tester has not been used for
a week, it is advisable to clean the probe tip using an oxidation removal sheet to attain consistent
and accurate reading.
b. Hold the probe pen with pen tip forming the right angle (90 degree) with an oxidation removal.
Gently move in a circular motion without retracting the tip
(Fig. 1.5)
.
16
a. Ensure the unit is switched off.
c. Repeat the same motion several times. The cleaning process is completed and tester is now
ready for use.
11
1
2
3
6
8
10
4
7
9
5
l. INTRODUCTION
04
ll. ABOUT THE SMARTPRO FINDER I
05
lll. IMPORTANT NOTICE
10
1. GETTING STARTED
12
2. PERFORMING A TEST
24
3. READING TEST RESULTS
27
4. TAKING CARE
28
CONTENTS
1. GETTING STARTED with SmartPro Finder I
Powering up
19
This tester can be powered by the use of batteries. Required AAA Batteries (x2), take note of
the positive (+) and negative (-) directions of batteries
(Fig 1.1).
The use of Alkaline batteries is
preferred, as it should generally give approximately 2.5 hours continuous operation, While the
use of ordinary batteries will give a shorter working life.
Press the [ON/OFF] button
(Fig. 1.3)
and wait for warm up the tester about 20 seconds.
10
12
14
The recommended testing temperature is 18
o
C - 27
o
C or 65
o
F - 80
o
F Please allow the gemstone or
jewelry piece to adjust to room temperature prior to testing. Exposure and/or operation of the tester
outside the room temperature would affect the result and performance of tester.
The probe tip must be placed at the right angle or perpendicular to the facet of gemstone for an
accurate reading.
Tests should be conducted on the table of the gemstone. In the event of any doubt, kindly test on
the girdle of the gemstones instead.
To achieve optimum accuracy for tests involving very small, it is important to allow the gemstone
to cool down before subsequent tests.
a. Keep the tester dry. Precipitation and all types of liquids or moisture can contain minerals that
will corrode electronic circuits. If your tester does get wet, remove the battery, and allow the
tester to dry completely before replacing it.
b. Do not use, store or expose the tester industry and dirty areas. It’s moving part and electronic
components can be damage.
c. Do not use, store or expose the tester in hot areas. High temperatures can damage or shorten
the life of the tester, damage batteries, and warp or melt certain plastics.
d. Do not use, store or expose the tester in cold areas. When the tester returns to its normal tem-
perature, moisture can form inside the device and damage electronic circuit boards.
e. Do not attempt to open the tester other than as instructed in user manual book.
III. IMPORTANT NOTICE
Fig. 1.1
Fig. 1.3
17
Fig. 1.5
While in this preparation mode, you can check status through the ORANGE “Ready” LED will blink
continuously until has the steady lighting with beep sound It’s means your tester is ready now for
use
(Fig.1.4)
.
15
Fig. 1.4
