background image

                                   

HGM8110DC-2 GENSET CONTROLLER USER MANUAL 

HGM8110DC-2 Genset Controller                    2020-02-20                  Version 1.0                Page 50 of 69 

8.3

 

DEFINED CONTENTS OF CONFIGURABLE INPUT PORTS (All Active when connect to 

Ground (B-))   

Table 15 - Defined Contents of Programmable Inputs 

No.   

Type   

Description   

Users Configured 

Including following functions, 

Indication: indicate only, not warning or shutdown.   

Warning: warn only, not shutdown.   

Shutdown: alarm and shutdown immediately   

Trip and stop: alarm, generator unloads and shutdown after 

hi-speed cooling   

Trip: alarm, generator unloads but not shutdown.   

Never: input inactive. 

Always: input is active all the time. 

From crank: detecting as soon as start. 

From safety on: detecting after safety on run delay. 

Reserved 

 

Alarm Mute 

Can prohibit ―Audible Alarm‖ output when input is active.   

Reset Alarm 

Can reset shutdown alarm and trip alarm when input is active.   

60Hz Active 

Use for CANBUS engine and it is 60Hz when input is active.   

Lamp Test 

All LED indicators are illuminated when input is active.     

Panel Lock 

All buttons in panel are inactive except navigation and exit 

buttons and there is 

  on the right of first row in LCD when 

input is active.   

War Mode 

All shutdown alarms except alarms of emergency stop and 

over speed shutdown cannot stop the engine in the war 

mode.   

Idle Mode 

Under voltage/frequency/speed protection is inactive. 

Auto Stop Inhibit 

In 

Auto

 mode, during generator normal running, when input 

is active, inhibit generator shutdown automatically. 

10 

Auto Start Inhibit 

In 

Auto

 mode, inhibit generator start automatically when input 

is active. 

11 

Scheduled Run Inhibit 

In 

Auto

 mode, inhibit scheduled run genset when input is 

active. 

12 

Reserved 

 

13 

Generator Close Status 

Connect generator loading switch‘s Aux. Point.   

14 

Generator Load Inhibit 

Prohibit genset switch on when input is active. 

15 

Reserved 

 

16 

Reserved 

 

17 

Auto Mode Lock 

When input is active, controller enters into auto mode; mode 

selection buttons are inactive. 

18 

Auto Mode Inhibit 

When input is active, controller won‘t work under auto mode. 
Auto mode key and simulate auto key input does not work. 

19 

Reserved 

 

20 

Reserved 

 

Содержание HGM8110DC-1






































































Отзывы: