Smartgen ACC4100 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 52

background image

ACC4100 Diesel Air Compressor Controller User Manual Page 21 of 52

No.

Item

Range

Default

Description

7

Warming Up Time

(0-3600)s

0

Warming up time for engine before normal
running after high speed running.

8

Cooling Time

(0-3600)s

0

Cooling time before stop

9

Stop Idle Time

(0-3600)s

10

Time for engine idle running in stop
process.

10

ETS Solenoid Hold

(0-3600)s

20

Time for ETS to be energized before stop.

11

Wait Stop Time

(0-3600)s

0

Time after idle running delay before
complete stop when ETS Solenoid Hold is
set 0; When it is not 0, it is time after ETS
delay before complete stop.

12

After Stop Time

(0-3600)s

0

Time from complete stop to standby
status.

13

Fuel Pre-supply Rest
Time

(0-12)h

2

Interval  time  from  this  pre-supply  is
completed  to  next  pre-supply  is  outputted
when  output  is  configured  to  fuel
pre-supply  in  standby  state;  when  it  is  set
to  0,  pre-supply  will  not  output  in  standby
state.

14

Fuel Pre-supply Time

(3-30)s

5

Time for pre-supply output when output is
configured to fuel pre-supply.

Engine Setting
1

Engine Type

(0-39)

34

Default: 34: GTSC1;

2

Enable ECU Alarm Shut

(0-1)

1

0: Disable 1: Enable

NOTE:

When engine detects red light alarm, it will

stop when it is enabled;

3

Source of Speed Signal

(0-1)

0

0: Speed Sensor 1: W/L

4

W/L Ratio

(0-99.99)

9.04

5

Flywheel Teeth

(1.0-300.0)

118.0

Flywheel  teeth  of  engine,  used  for  starter
disconnect  conditions  and  engine  speed
detection;  please  refer  to  the  below
installation.

6

Rated Speed

(0-6000)r/min 2200

Provide standard for over speed, under
speed and load speed detection.

7

Start Attempts

(1-10)times

3

Maximum  start  times  in  case  of  failed
start;  when  this  number  is  reached,
controller shall issue Failed to Start signal.

8

Crank Disconnect

(0-2)

2

Please refer to Table 12;
There are two kinds of disconnect
conditions for engine and starter. They can
be used independently or together and the
purpose is to separate starter motor and
engine as soon as possible.

9

Disconnect Speed

(0-200)%

24

Set value is the percentage of rated speed;
when speed is above the set value, starter

«
...
19
20
21
22
23
...
»

Содержание ACC4100





















































Отзывы:

Нет отзывов

Похожие инструкции для ACC4100

Бренд: IBM Страницы: 144

Бренд: Aalborg Страницы: 15

Бренд: Aalborg Страницы: 48

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 21

Бренд: Daikin Страницы: 20

Бренд: Salda Страницы: 20

MorphoAccess SIGMA Extreme Series

Бренд: Safran Страницы: 79

Бренд: Lawler Страницы: 5

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: Madison AV Страницы: 2

Бренд: Polycom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды