OUTPUT 2
OUTPUT 1
INPUT 1 INPUT 2
EXPAN 1
EXPAN 2
A
B
+3V
SET
RST
N/O
COM
N/C
N/O
COM
N/C
+3V
SET
RST
A
B
FAULT
ACTIVE
RLY 1
RLY 2
7 Input wiring
Operating temperature
-10 to +55 °C
Storage temperature
With batteries
-10 to +30 °C
Without batteries
-10 to +55 °C
Humidity
0 to 95% noncondensing
Location
Type A: for indoor use
Supply
3 x ER14505M 3.6 V lithium thionyl chloride
batteries
(Fanso
or
Titus)
CAUTION!
Operating voltage
2.7 to 3.65 VDC
Operating frequency
868 MHz
Output transmitter power
14 dBm / 25 mW
Signalling protocol
X5
Dimensions (W x H x D)
150 x 200 x 55mm
Manufacturer
EMS Ltd. Technology House, Herne Bay, Kent, CT6 8JZ.
United
Kingdom
Year of manufacture
See devices serial number label
Certification
Certification body
CPR certificate DoP
0359-CPR-00269
Approved to
EN54-13:2005. Fire detection and fire alarm systems.
Part 13: compatibility assessment of system
components.
EN54-18:2005. Fire detection and fire alarm systems.
Part 18: input/output devices.
EN54-25:2008. Incorporating corrigenda september
2010 and march 2012. Fire detection and fire alarm
systems. Part 25: components using radio links.
European Union
EMS declares that the radio equipment type SmartCell
directives Dual Input / Output Device is in compliance with
Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following
internet
address:
www.mysmartcell.co.uk
2012/19/EC (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information
see
www.recyclethis.info
Dispose of your batteries in an environmentally
friendly manner according to your local regulations.
19
Two resistor monitored inputs are
available.
Both inputs monitor; normal,
alarm, open circuit and closed
circuit conditions.
Each input is factory fitted with an
end of line 20 kΩ resistor.
To connect inputs to external
devices, wire as shown, using the
resistors provided.
Minimum input detection time is 2
seconds.
If an input is not being used, leave
the 20 kΩ resistor as factory fitted.
Two outputs are available.
Both outputs are voltage free,
with a maximum switching
capacity of 30 V at 1 A.
This product contains relays which when subjected to severe mechanical shock
may cause momentary transitions from the currently active state. The
transitions will be less than 1 second and any equipment connected must not
respond to such momentary changes of the relay. This product should be fixed
to a stable and secure structure that is not subject to severe mechanical shock.
0359
OUTPUT 1 OUTPUT 2
N/O CO
M
N/C
N/O CO
M
N/C
20k 4k7
C
N/O
EOL resistor
configuration
Remote monitored device
A
B
INPUT 1
A
B
INPUT 2
Note: max cable
length of 10 m
20kΩ
!
9 LED operation
10 Completing the installation
Output 1
LED
Output 2
LED
Input 2
LEDs
Input 1
LEDs
The front lid must now be re fitted to the device and all four fixing screws
tightened to fully reassemble the unit.
The device has six indication LEDs. They operate as follows:
Input fault:
YELLOW LED ON
Input active:
RED LED ON
Output active:
RED LED ON
Application label
This can be utilised to
identify connected
circuits as per the
above example
Status LED location
This status LED is
multi functional.
See
programming manual
(TSD155)
for full
details of operation
WARNING. DO NOT CONNECT TO MAINS.
Specification
Regulatory information
STATUS
DUAL INPUT/OUTPUT DEVICE
LOG ON POINT
Input 1: BEAM DETECTION
Input 2: GAS DETECTION
Output 1: FAN SHUT OFF
Output 2: GAS SHUT OFF
©2020 EMS Ltd. All rights reserved. Page 1 of 2
TSD089-0001-99 (Issue 1) 12/05/2020 AJM
This is a life safety product. Only use manufacturer approved battery types.
Failure to do so may result in damage to the product.
DO NOT mix batteries of different type or age.
When replacing batteries; remove all old batteries before fitting replacements.
