SMAR DT302 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 84

SMAR DT302 Скачать руководство пользователя страница 55

Configuration

3.21

Calibrating Using Local Adjustment

In order to follow the example bellow the Display Transducer block should be configured to show
these parameters: CAL_POINT_HI (mnemonic UPPER), CAL_POINT_LO (mnemonic LOWER)
and TAG (mnemonic TAG).

The  transmitter  has two holes for magnetic switches, located under the identification plate. These
magnetic switches are activated by one magnetic tool.

This magnetic tool enables adjustment of the most important parameters of the blocks. It also
enables pre-configuration of the communication.

The jumper w1 on top of the main circuit board must be in place and the transmitter must be fitted
with the digital display for access to the local adjustment. Without the display the local adjustment is
not possible.

In order to enter the local  adjustment mode, place the magnetic tool in orifice “Z” until flag “MD”
lights up in the display. Removes magnetic tool from “Z” and place it in orifice “S”. Remove and
reinsert the magnetic tool in “S” until the message “LOC ADJ” is displayed.

The message will be displayed during approximately 5 seconds after the user removes the magnetic
tool from “S”. By placing the magnetic tool in “Z” the user will be able to access the local
adjustment/monitoring tree.

The jumper W1 on top of the main circuit board must be in place and the transmitter must be fitted
with digital display for access to the local adjustment. Without display, the local adjustment is not
possible.

Figure 3.16 - Local Adjustment

Table 3.4 shows the actions on the

Z

and

S

holes on the

DT302

when Local Adjustment is enabled.

HOLE

ACTION

Z

Initializes and rotates through the available functions.

S

Selects the function shown in the display.

Table 3.4 - Purpose of the holes on the Housing

J1 Jumper Connections

If J1 (see figure 3.21) is connected to ON, then simulation mode in the AI block is enabled.

«
...
53
54
55
56
57
...
»

Содержание DT302





















































































Отзывы:

Нет отзывов