Small Wonder Labs PSK-20 Скачать руководство пользователя страница 13

Страница: 13 / 26

Small Wonder Labs



PSK-20 Transceiver Kit 03/09/10



2000

Group 2 Assembly:

Group 2 assembly installs the receiver 'back-end'
circuitry.

Install 3.5 mm (1/8") audio jacks at J1-J3.

Install 8-pin IC sockets at U3 and U4. Match
the 'notch' orientations as shown on the
silkscreen.

Install R20 (220

Ω

, red/red/brown).

Install R19 (4.7K, ylw/violet/red).

Install electrolytic cap C18 (10 uF). Observe
the polarity marking on the device.

Install R16 (510K, green/brn/ylw).

Install R17 (10

Ω

, brown/blk/blk).

Install R14 (1K, brown/blk /red).

Install D8 (1N5236- from 'Zeners' envelope).
Match the orientation of the banded end of the
component to that of the silkscreen.

Install C17 (47 pF disk cap).

Install electrolytic cap C107 (220 uF).
Observe the polarity marking on the device.

Note: there is no silkscreened reference
designator for this part.

Install C14 (.022 uF monolithic cap), '223'

Install C15 and C19 (.1 uF monolithic caps),
'104'

Install R15 (10K, brown/blk /orange).

Install C16 and C108 (.01 uF disk caps).

Install C106 (.01 uF disk cap).

Install diodes D5 and D6 (1N4148). Observe
the installation polarity as shown on the
silkscreen.

Install electrolytic cap C20 (3.3 uF). Observe
the installation polarity as shown on the
silkscreen.

Install R21 (1 Megohm, brn/blk/green.)

Install R23 (10K, brn/blk/orange).

Install R22 (33K, orange/org/org).

Install R18 ((10K, brn/blk/orange).

Install C13 (22pF disk cap).

Install D15 (1N4148). Match the orientation
of the banded end of the component to that of
the silkscreen.

Install IF transformer T1.

Caution

: Ensure

that you install the transformer marked
'42IF123' in this location.

The slug in this

transformer is colored green.

Install Q12 (2N7000- from antistatic bag).
Match the orientation of the flat side of the
component to that of the silkscreen.

This part

is static-sensitive

MICR.

R20

R19

220

4.7K

8 - +

10 uF

- +

C20

3.3

C17

47 pF

510K

- +

C107

C106

.01

220 uF

R17

R14

C15

.022

.01

R15

10K

Q12

R22

33K

R21

R23

10K

C13

R18

.01

10K

LINE
OUT

C14

Содержание PSK-20



























Результаты поиска

Содержание PSK-20

Отзывы:

Похожие инструкции для PSK-20

Бренды по названию

Популярные бренды

Small Wonder Labs PSK-20, Инструкция по эксплуатации

Результаты поиска

Содержание PSK-20

Отзывы:

Похожие инструкции для PSK-20

Бренды по названию

Популярные бренды