Please Note: Coaxial cable, mountings and masts are not supplied with this aerial. You will need to select these from the range
available according to the specific requirements of your installation. The quality of the coaxial cable used is as important as
the quality of the aerial and you should make sure that if it is not specifically marked as suitable for digital TV it is of the same
quality as that used for digital satellite installations.
For best results the aerial should be mounted on an outdoor aerial mast and
pointed in the direction of the nearest transmitter* making sure it is in a position
where the transmitter signal will not be obstructed by nearby trees and buildings.
If you are in any doubt about the direction in which the aerial should be pointing
or the orientation of the aerial (horizontal for main transmitter, vertical for relay
transmitter) check your neighbours’ aerials.
If mounting on an existing mast check that the mast is in good condition and
firmly fixed.
1. Using the clamp supplied fix the aerial to the mast - see Fig. 8 & 9.
2. After the aerial direction has been fine tuned for best reception tighten the
bolts firmly until the aerial is securely fixed to the mast.
Please note that this aerial can also be loft mounted.
For optimum performance it is very important that the coax cable
should be routed as shown in Fig. 8.
Do NoT allow The Cable To TouCh The aerial
boom aT aNY PoiNT.
PVC insulation tape can be used as shown to hold the cable in place.
1x Central boom: assembly square aluminium (l) approx 780mm
with 5x ‘X’ type elements assemembled
2x reflector booms: Square aluminium (l) approx 330mm with
8x reflector elements: Curved aluminium (l) approx 500mm
1x bow tie shaped dipole and printed circuit balun
1x Tilting mast clamp
braid
centre wire
5mm
10mm
8mm
central
terminal
braid
clamp
CauTioN: when mounting the assembled aerial, always observe safety
precautions and use the correct equipment. unless you are competent in
the use of ladders and other access equipment, do not work outdoors at
roof height. if in any doubt, refer to a qualified aerial installer.
mast
clamp
aerial
boom
PVC
insulation
tape
Fig. 8
other useful websites for Digital advice:
*
To confirm that your home is in a coverage area, to find
out what DTT channels should be available locally and to
find out where your nearest transmitter is (distance and
compass bearing) visit:
Digital uK website
:
www.dtg.org.uk/industry/coverage.html
No picture:
Check all connections from aerial to TV.
Poor picture:
Check all connections from aerial to TV.
Check aerial is properly aligned to the correct transmitter.
If the aerial has been loft mounted try mounting outside.
Make sure new digital coax cable has been used throughout the
installation.
Check the transmitter signal is not obstructed by nearby trees
or buildings.
If in a very weak signal area or for long cable runs, installing a
masthead amplifier will improve the signal.
If in a strong signal area the signal strength may need to be
reduced by fitting an attenuator.
Fig. 6
Fig. 7
1. Before preparing and stripping the cable ready for connection,
feed the coax cable through the hole in the terminal cover.
2. Prepare cable as shown in Fig. 6
3. Feed prepared cable through the braid clamp and thread the
centre wire through the hole in the central terminal as shown
in Fig. 7.
4. Clamp the cable braid securely first, then tighten the screw on
the central terminal. Trim any stray braid that might come into
contact with the centre wire or central terminal.
5. Replace terminal cover carefully and securely making sure that
the cable is not trapped or kinked.
Tilting
Mast Clamp
Fig. 9
Adjust aerial
to horizontal
before
tightening
bolts
Coax plug* wiring instructions
1 Unscrew coax plug housing and slide cap
over cable.
2 Strip 23mm of cable outer sheath.
Gather copper braid, wrap around outer
sheath, slide claw over braid and crimp.
3 Strip 18mm of inner insulation to leave 5mm
exposed
4 Undo screw on plug/clamp, slide clamp over
inner wire & tighten screw. Reassemble plug
1
2
3
4
5
5 Trim inner wire flush with plug.
*
Coax plug not supplied
PLEASE NOTE: A coax plug is not included with
this aerial. If you need to fit one please follow the
wiring instructions shown below.
E. Coax cable routing
Box contents
F. Fixing to a mast
D. Connecting coax cable
Troubleshooting
Customer Careline:
08457 573 479
Local rate UK only
Technical website:
www.philex.com/support
e-mail Support:
© Philex Electronic Ltd 2013. v1.1 www.philex.com