1. Use as directed:
ENG
Instruction Manual LALU 1/2
This product serves exclusively lighting purposes and may:
only be used with a voltage of
230V ~50Hz
.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2. Technical Data:
Operating voltage:
230V ~50Hz
Safety class:
I
Safety type:
IP 43
Bulb:
TC-DSE,
E27,
max.15W
Dimensions (W/H/D):
25/27,5/15 cm
Weight:
1,5
kg
Importeur:
SLV
Elektronik
GmbH
IP 43
: Protection against foreign objects > Ø 1,0mm - Protection against
spraying water up to 60° to the vertical.
3. Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention:
Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
.
Use only parts, which are supplied with the product or are described as
accessories! Otherwise the product or the installation might not be
sufficiently safe.
Installation place:
The product is suited for
wall installation
.
Make sure that the product is mounted on a
stable, even and tilt-fixed
background
. To preserve the safety type IP 43 it is necessary to install the
product with the socket on the downside.
Separate Installation Steps
Loosen the two screws(1) to remove the acrylic cover(2).
Remove the mounting plate cover (3).
Determine the place of installation and mark the holes to be drilled. Note
that the cable outlet of the power supply line fits between the mounting
bracket and the canopy. Do not damage the power supply line, e.g. by
drilling, screws or strong bending.
Direct the mains lead through the rubber gasket.
Fasten the mounting plate to the mounting surface (4).
Electrical Connection (5)
The product must be able to be separated by an all pole separation from
the current supply.
Equip the three wire ends with protective tubes.
For electric connection attach the black or brown wire (live conductor) of
the mains supply with the
clamp L
and the blue wire (neutral conductor)
of the mains supply with the
clamp N
. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the
earth
clamp
of the product.
Inserting the bulb:
Touch
energy-saving-lamps
on the plastic
housing, not on the bulb glass. Screw the bulb jnto the socket (6).
Now fasten the cover of the mounting plate.
Do not forget to apply the
toothed washers!
Apply the acrylic cover.
Ensure that the light fixture holds securely!
The product is now ready for operation.
4. Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention:
Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
high salt content in the air
thawing salt
cleaning agents
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Cleaning tip
: Switch off power! Clean the product with a damp
cloth.
What is to do if a bulb is defect or does not work?
IP 43
IP 43
L
N
1
2
3
5
6
4
Disconnect the product from power
, before you exchange the bulbs.
Caution
: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb
: see Installation.
Attention: Do not use incandescent bulbs!
5. What else has to be considered?
Disconnect the product from power
, before you…
clean or maintain the product.
do any works on the product or its components (electric expert).
229512 08/2006
by SLV Elektronik GmbH
Technical Details are subject to change.
Duplication prohibited !
F
Mode d'emploi
LALU 1/2
1. A utiliser comme indiqué :
Ce produit ne sert qu’à éclairer:
il est prévu pour une tension de
230V ~50Hz.
il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
il ne doit être utilisé qu’après examen si le produit a été stocké dans un
entrepôt humide ou sale.
il ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2. Informations techniques:
Tension d'alimentation:
230V ~50Hz
Classe de protection:
I
Degré de protection:
IP 43
Ampoule:
TC-DSE, E27, max.15W
Dimensions (L/H/P):
25/27,5/15 cm
Poids: 1,5
kg
Importateur:
SLV
Elektronik
GmbH
IP 43
: Protection contre les corps étrangers durs > 1,0 mm - Protection
contre l’eau vaporisée venant de la verticale jusqu’à 60°.
3. Installation
La connection électrique doit être exécutée par un professionnel,
lequel est familier des normes en vigueur!
Attention: Mettez l’alimentation électrique ou le raccordement au
secteur hors tension avant de travailler!
Utilisez seulement des pièces qui ont été livrées avec le produit ou qui sont
uniquement décrites comme accessoires ! Sinon, l’installation ainsi que le
produit ne peuvent pas être garantis.
Lieu d'installation
Ce produit est fait pour un montage
au mur.
Veillez à ce que le produit soit
monté de manière
stable et résistante au basculement. Pour la
préservation de la protection IP 43, la douille doit montrer vers le bas
pendant le montage.
Etapes successives pour installer le luminaire
Dévissez les deux vis (1) et enlevez le couvercle acrylique (2).
Enlevez la plaque de montage de la boîte de la rosette de la lampe en
dévissant les deux vis latérales (3).
