ENG
Instruction Manual for BEAM G9
1. Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of
230V ~50Hz
.
not be operated indoors.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2. Technical Data:
Operating voltage:
230V ~50Hz
Safety class:
I
Safety type:
IP 44
Bulb:
QT14,G9,
max.
60W
Dimensions (L/W/H):
8/8/15,3 cm
Weight: 1,15
kg
Importeur:
SLV
Elektronik
GmbH
IP 44
: Protection against foreign objects > Ø 1,0mm - Protection against
splashing water from all directions.
3. Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention:
Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
.
Use only
parts, which are supplied with the product or are described as accessories!
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for
wall installation
.
Make sure that the product is mounted on a
stable, even and tilt-fixed
background
.
The
light exit
should be placed at least so far from the illuminated surface,
as indicated as
minimum distance
on the type plate of the luminaire:
0,5
m
.
Pay special caution
to easily inflammable objects (e.g. foliage).
Separate Installation Steps
Remove the mounting plate from the housing by loosening the two
screws on the sides (1).
Determine the place of installation and mark the holes to be drilled. Note
that the cable outlet of the mains supply corresponds with the cable inlet
of the fixture. Do not damage the power supply line, e.g. by drilling,
screws or strong bending.
Direct the power supply line through the cable inlet on the mounting
plate(2).
Fasten the mounting plate to the mounting surface (3).
Electrical Connection
The product must be able to be separated by an all pole separation from
the current supply.
Equip the three wire ends with protective tubes(4).
For electric connection attach the black or brown wire (live conductor) of
the mains supply with the
clamp L
and the blue wire (neutral conductor)
of the mains supply with the
clamp N
. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the
earth
clamp
of the product (5).
Inserting the bulb:
Use a piece of fabric to insert the bulbs. Do not
touch them with bare fingers. Stick the bulb into the socket.
Now fasten the housing back on the mounting plate.
Do not forget to
apply the toothed washers!
Pay attention that the gasket is properly
seated.
Ensure that the light fixture holds securely!
The product is now ready for operation.
4. Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention:
Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
high salt content in the air
thawing salt
cleaning agents
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Cleaning tip
: Switch off power! Clean the product with a damp
cloth.
What is to do if a bulb is defect or does not work?
Disconnect the product from power
, before you exchange the bulbs.
Caution
: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb
: see Installation.
5. What else has to be considered?
Disconnect the product from power
, before you…
clean or maintain the product.
do any works on the product or its components (electric expert).
227064/65 01/2006
by SLV Elektronik GmbH
Technical Details are subject to change.
Duplication prohibited !
F
Mode d'emploi pour
BEAM G9
1. A utiliser comme indiqué :
Ce produit ne sert qu’à éclairer:
il est prévu pour une tension de
230V ~50Hz.
1
4
5
3
2
L N
ne doit pas être exploité dans les zones intérieures.
il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
il ne doit être utilisé qu’après examen si le produit a été stocké dans un
entrepôt humide ou sale.
il ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2. Informations techniques:
Tension d'alimentation:
230V ~50Hz
Classe de protection:
I
Degré de protection:
IP 44
Ampoule:
QT14,G9, max. 60W
Dimensions (L/L/H):
8/8/15,3 cm
Poids: 1,15
kg
Importeur:
SLV
Elektronik
GmbH
IP 44
: Protection contre les corps étrangers durs > Ø 1,0 mm - Protection
contre les éclaboussures provenant de toutes les direction.
3. Installation
La connection électrique doit être exécutée par un professionnel,
lequel est familier des normes en vigueur!
Attention: Mettez l’alimentation électrique ou le raccordement au
secteur hors tension avant de travailler!
Utilisez seulement des pièces qui ont été livrées avec le produit ou qui sont
uniquement décrites comme accessoires ! Sinon, l’installation ainsi que le
produit ne peuvent pas être garantis.
Lieu d'installation
Ce produit est fait pour un montage
au mur.
Veillez à ce que le produit soit
monté de manière
stable et résistante au basculement.
La distance entre
la sortie de lumière
et la face illuminée devrait au moins
être tant que
la distance minimale
indiquée sur l’étiquette du type du
lumière:
0,5 m
.
Soyez prudent
avec les matières inflammables (comme
rideaux etc.).
Etapes successives pour installer le luminaire
Enlevez la plaque de montage de la lampe en dévissant les deux vis
latérales(1).
Déterminez l’emplacement du montage et marquez les trous de fixation :
l’entrée du câble de la lampe doit correspondre à la sortie du câble du
réseau électrique. Soyez attentif à ce que le câble d'alimentation ne soit
pas endommagé.
Faites passer l’adduction à travers le joint (2).
Fixez la plaque de montage à la face de montage(3).
