1. Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of
230V ~50Hz
.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2. Technical Data:
229874/76 229884/86
Operating voltage:
230V ~50Hz
Safety class:
I
Safety type:
IP 44
QPAR111,GU10,
Bulb:
max.75W max.50W
Dimensions W/H/D:
16/10/18,5 cm
Ø/H: 16,3/9,4 cm
Weight
0,70 kg
0,65 kg
Importer: SLV
Elektronik
GmbH
IP 44
: Protection against foreign objects > Ø 1,0mm - Protection against
splashing water from all directions.
3. Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention:
Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
.
Use only parts, which are supplied with the product or are described as
accessories! Otherwise the product or the installation might not be
sufficiently safe.
Installation place:
Make sure that the product is mounted on a
stable, even and tilt-fixed
background
.
The
light exit
should be placed at least so far from the illuminated surface,
as indicated as
minimum distance
on the type plate of the luminaire:
.
Pay special caution
to easily inflammable objects (e.g.
foliage).
229874/76: Install the fitting only with the light exit pointing
downwards.
Separate Installation Steps
229874/76
: Remove the mounting plate from the fitting by loosening the
two screws on the side of the canopy.
229884/86
: Remove the protection glass.
Determine the place of installation and mark the holes to be drilled. Note
that the cable outlet of the power supply line fits between the mounting
bracket and the canopy. Do not damage the power supply line, e.g. by
drilling, screws or strong bending.
229874/76
: Fasten the mounting plate to the mounting surface.
229884/86
: Fasten the fitting to the mounting surface.
Electrical Connection
The product must be able to be separated by an all pole separation from
the current supply.
Equip the three wire ends with protective tubes.
For electric connection attach the black or brown wire (live conductor) of
the mains supply with the
clamp L
and the blue wire (neutral conductor)
of the mains supply with the
clamp N
. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the
earth
clamp
of the product.
229874/76
: Now fasten the fitting back to the mounting plate.
Do not
forget to apply the toothed washers!
Remove the protection glass.
Inserting the bulb:
Insert the bulb with a quarter-turn to the right.
Put the protection glass back on.
Ensure that the light fitting is kept securely!
The product is now ready for operation.
4. Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention:
Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
high salt content in the air
thawing salt
cleaning agents
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Cleaning tip
: Switch off power! Clean the product with a damp
cloth.
What is to do if a bulb is defect or does not work?
Disconnect the product from power
, before you exchange the bulbs.
Caution
: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb
: see Installation.
5. What else has to be considered?
Disconnect the product from power
, before you…
clean or maintain the product.
do any works on the product or its components (electric expert).
229874/76/84/86 01/2006
©
by SLV Elektronik GmbH
Technical Details are subject to change.
Duplication prohibited !
L
N
IP44
IP44
ENGLISH
Instruction Manual
for Outdoor Light Fittings
229874/76/84/86
Please read carefully and keep for further reference !
