if in-wall carrier is not used. Use a
masonry bit to drill hole, then install
A.
Hang the bowl on the bracket
and check tail
pipe alignment, then remove the bowl and
adjust the bracket as needed.
Re-hang and re-check bowl
alignment with
the drain line. Tail pipe should align with center
of drain line.
B.
Mark anchor holes
then
remove bowl without
moving hanger bracket.
A.
Find the drain nipple depth
on
the Tube Cutting Chart (left).
Measure and mark the specified
trim length
on the insert tube at
the nearest ¼” groove.
B.
Cut the tube
at the groove using a sharp
utility knife to ensure a square, flat cut.
C.
Clean burrs
from the cut end by using
emery paper.
D.
Apply lubricant
to the outside of the
rubber bushing and ribbed inside area.
E.
Insert the tube
and bushing with arrow
tab at the top. Apply lubricant to tailpipe
of housing.
IMPORTANT:
Be sure arrow tab
is art 12:00 position.
USE UTILITY KNIFE TO CUT CAULK
then
use a putty knife and mallet to remove
the bowl. Remove hanger brackets,
scrape off caulk, and clean the wall.
MEASURE & MARK THE ROUGH-IN
"
the hanger bracket with one plastic
anchor and screw.
DETERMINE THE DRAIN NIPPLE DEPTH
by measuring the distance between the
back of the sanitary tee (or elbow) to the
front edge of the nipple.
IMPORTANT:
Use a drain machine to
remove build-up inside pipes. Clean up
to 25 feet deep then flush with water to
remove cutting debris. Never install on
copper DWV.
A.
Clean face
of existing wall flange.
B.
Install the brass flange
with the clear
inspection disc.
C.
Slowly pour water
into the drain.
D.
Use a flashlight to check the pitch/
slope
. No water should be present in
the inspection disc or nipple.
E.
Remove flange and disc
after inspection.
ADJUST DRAIN TO ACHIEVE PITCH
only if standing water is present
(code requires ¼” drop per foot of
drain line for proper pitch). Seal wall
according to code.
PLACE THE SEAL INTO THE FLANGE
with
the ribs facing out. Install the flange
with washers and hex nuts, but do not
tighten completely.
HANG THE BOWL,
inserting
tailpipe into bushing, then
install anchor screws with
washers.
TIGHTEN FLANGE
BOLTS AND HOSE CLAMP.
POUR 5
GALLONS
OF WATER
as rapidly
as possible
into housing
to ensure
good flow
and no leaks or
standing water.
INSTALL THE HOSE CLAMP
with screw head at bottom,
but do not tighten.
CAULK THE BOWL
TO THE WALL
if
there is good flow
and no leaks or
standing water.
INSTALL
CARTRIDGE
per the cartridge
instruction sheet.
2" side cutter blade
Cut away wall
Lift drain line & brace
with mending plate
13 ⁄ "
Install plastic anchor
and screw here
INCORRECT
Not centered
CORRECT
Centered
11
10
12
CARTRIDGE
INSTRUCTIONS
1
2
3
4
Arrow
tab UP
1
2
3
4
A
C
B
D
E
"
14
15
4
13
3
12
8
6
2
10
11
9
7
5
1
C
D
A
B
WES-7000 WATERFREE URINAL
RETROFIT
INSTALLATION INSTRUCTIONS
BEFORE STARTING INSTALLATION:
IMPORTANT
Do not install on copper DWV
due to copper’s susceptibility to corrosion.
Check rough-in height to achieve 24” rim height
(17” rim height for ADA).
Check slope. Downhill slope, per code, is essential
because waterfree urinals depend on gravity flow.
Check DWV material. Suitable materials include
cast iron, PVC, ABS and galvanized steel.
Shut off water supply and cap the nipple with 3/4“
chrome cap (provided).
TUBE CUTTING CHART
Measure drain nipple depth (inches) to find trim
length (inches)
13 7/8” or more DO NOT CUT
3 3/4” or less DO NOT USE TUBE
•
•
•
•
•
•
OR LESS
TRIM
13 ¾"
¼"
13 ½
½
13 ¼
¾
13
1
12 ¾
1¼
12 ½
1½
12 ¼
1¾
12
2
11 ¾
2¼
11 ½
2½
11 ¼
2¾
11
3
10 ¾
3 ¼
10 ½
3 ½
OR LESS
TRIM
10 ¼"
3 ¾"
10
4
9 ¾
4 ¼
9 ½
4 ½
9 ¼
4 ¾
9
5
8 ¾
5 ¼
8 ½
5 ½
8 ¼
5 ¾
8
6
7 ¾
6 ¼
7 ½
6 ½
7 ¼
6 ¾
7
7
OR LESS
TRIM
6 ¾"
7 ¼"
6 ½
7 ½
6 ¼
7 ¾
6
8
5 ¾
8 ¼
5 ½
8 ½
5 ¼
8 ¾
5
9
4 ¾
9 ¼
4 ½
9 ½
4 ¼
9 ¾
4
10
CUSTOMER SERVICE
1-888-SLOAN-14 (1-888-756-2814)
www.sloanvalve.com
The information in this document is subject to change without notice.
© 2015 Sloan Valve Company All rights reserved.
(08-15)Rev1
CAUTION
After removing any urinal from the
drain line, it’s normal for certain naturally occurring,
but
potentially hazardous sewer gases
to escape
through the opening until the waterless cartridge
is installed properly into the waterless urinal. If you
need to leave an open drain line unattended after
removing the urinal from the wall, temporarily wedge paper towels or a
rag into the drain hole to reduce any outflow of sewer gases, and remove
the paper towels or rag prior to completing the urinal or cartridge
installation.
Never smoke, have an open flame, or place your nose or
mouth near open drain lines or waterless urinal housings into which
a cartridge is not yet properly installed.
You also can wear a breathing
mask when removing or installing any waterless urinal or cartridge to
reduce potential exposure to any such gases.
•
LUBRICANT
Install two
additional screws
•
DRILL HOLES
masonry bit for the
lower anchor screws and mounting plate
and insert plastic anchors where indicated.