lEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. the dust from the removal of such paint is toxic if inhaled or ingested and must, therefore,
be avoided. the following action must be taken before using the sander/polisher on a surface that you suspect may have contained lead in the
paint.
1. User must determine potential hazard relating to age of paint to be removed. (Modern paints do not contain lead).
2.
DANGER!
Keep all persons and pets away from the work area. the following are particularly vulnerable to the effects of lead paint dust:
Expectant women, babies and children.
3. We recommend personal protection by using the following safety items:
a
) Paint Spray Respirator
b
) PE Coated Hooded Coverall
c
) latex Gloves
4. take adequate measures to contain the paint dust, flakes, and scrapings.
5. Continue to wear safety equipment as in 3 above, and thoroughly clean all areas when task is complete. Ensure that paint waste is disposed of,
in sealed bags or containers, according to local authority regulations.
Model No:............................................. SlIMS149
Power:................................................... 600W
No load speed:...................................... 1500-6800rpm
PADS: SlIMS149
Orbit size:.............................................. ø8mm
Optional Pad: PtC/150A Stick-on (Firm)
Pad:....................................................... ø150mm
Optional Pad: PtC/150SA (supplied) Stick-on(Soft)
thread:.................................................. 5/16”UNF
Replacement Pad: PtC/150VA
Weight:.................................................. 2.26 kg
Vibration:............................................... 2.3m/s²
Uncertainty:............................................1.15m/s²
Noise power:..........................................91dB(A)
Noise pressure:................................... 80dB(A)
WARNING!
Before use, ensure that you have read and understood Section 1 Safety Instructions.
5.1.
Attach the correctly rated sanding disc (not supplied) to the sanding pad.
5.2.
Plug the sander/polisher into the mains power supply.
5.3.
Ensure that the speed scroll switch is set to the lowest setting before starting the sander/polisher (fig.1). Grip the handle and turn on by
pushing switch (fig.1) forward. let go of the switch and the machine will continue running. Increase the speed of the sander/polisher using
the variable switch located at the rear of the sander/polisher (fig.1).
Note:
the sander/polisher is designed for dry use only.
DO NOT
use with water or any other liquids.
WARNING!
DO NOT
plug sander/polisher into the mains power supply before it is fully assembled.
Screw the sanding pad onto the spindle (fig.1). to remove pad, hold spindle with the spanner supplied whilst unscrewing the pad.
Avoid unintentional starting.
DO NOT
use the sander/polisher for a task it is not designed to perform.
DO NOT
operate the sander/polisher if any parts are damaged or missing. this may cause failure and/or injury.
WARNING!
DO NOT
sand any materials containing asbestos.
DO NOT
carry the sander/polisher by the electrical cable.
DO NOT
connect to a standard vacuum cleaner to extract dust as damage to the cleaner may result.
DO NOT
get the sander/polisher wet or use in damp or wet locations.
DO NOT
use the sander/polisher with water, for dry use only.
DO NOT
operate the sander/polisher if you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
use where there are flammable liquids, solids or gases such as paint solvents or waste wiping or cleaning rags.
DO NOT
leave the sander/polisher running unattended.
DO NOT
carry the sander/polisher with your finger on the power switch.
When not in use disconnect from the power supply and store in a safe, dry, childproof area.
WARNING!
the warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied
by the operator.
lightweight, compact sander/polisher with variable speed control from 1500 to 6800rpm. Dual action orbit of Ø8mm helps cover more surface
during use. Powered by a 600W motor with a slide on/off switch on top. Soft-grip for added comfort. Supplied with mains cable.
3. SPECIFICATION
2. INTRODUCTION
4. ASSEMBly
5. OPERATION
fig.1
Original Language Version
SlIMS149 | Issue:2- 18/08/16
