Remember to follow the steps exactly as shown. Do not jump ahead, or you’ll get tangled up!
Step 5. - Attach Second Side Panel and Installing Corner Blocks
Step 6. - Attaching Cabinet Legs
Assemble adjustable leg by attaching the dowel head to
the leg (fig. 6, 6A, and 6B). Take the assembled leg and
insert dowel into the hole provided as in fig. 6A. Use
1/2” screws and screw leg into bottom of cabinet to
keep it firmly in place (fig. 6C and 6D). Let glue dry
Step 10. - Congratulations!
CONGRATULATIONS!
You have just finished
assembling and installing
a SLIDE-LOK cabinet.
Before Proceeding to the
next step, let glue dry
completely.
!
[ fig 5 ]
[ fig 5A ]
[ fig 5B ]
[ fig 5D ]
[ fig 5E ]
[ fig 6 ]
[ fig 6A ]
[ fig 6B ]
[ fig 6C ]
[ fig 6D ]
[ fig 5C ]
Repeat step 3 for the other side panel. See figures 5 & 5a. Take the corner blocks and 1/2”
screws, and attach to the face frame and side panel of cabinet, see figures 5B, 5C, & 5D.
Attach 2 corner blocks to each side of the cabinet, see figure 5E.
Step 7. - Fasten Cabinet to Wall
After glue is dry locate studs in
wall (fig. 7A). Attach cabinet to wall
using 2 1⁄2” screws. (See fig. 7)
NOTE:
It is important that the cabinet is set flush
to the wall and fastened to wall studs for
stability and strength.
Step 8. - Hang Cabinet Doors
To hang doors, use the 1 1⁄2” silver screws. Hold door up so
the door hinge hole lines up with the pre-drilled hole in the
face frame. Screw in the hinge so the doors are level across
the top and flush in the front. Take clear bumpers and attach
as in fig. 8B, to top and bottom of doors.
NOTE:
Hinge is 6 way adjustable
(up, down, in out, back
and forth) fig. 8A.
In and out
Up and Down
Back and Forth
[ fig 7 ]
[ fig 7A ]
[ fig 8 ]
[ fig 8A ]
[ fig 8B ]
Step 9. - Installing Optional Adjustable Shelf
To install shelf, use all 4 shelf clips. Push shelf clip into
holes, as in fig. 9, on side panel. Make sure the clips are
level in front, back and on the other side panel, see fig. 9A
Angle shelf and slide into cabinet, setting one side of shelf
on top of shelf clip, see fig. 9B. Let shelf drop onto the other
side and snap into place, see fig. 9C. To secure screw into
underside of shelf as in Fig. 9D.
[ fig 9 ]
[ fig 9A ]
[ fig 9B ]
[ fig 9C ]
[ fig 9D ]
DO NOT TO OVERTIGHTEN!
It is recommended that you finish
tightening with a screwdriver to avoid
stripping the pre-drilled holes.
!
If you purchased a shelf package continue with Step 9, otherwise skip this step.
NOTE: - Attaching Two or More Cabinets
When putting two cabinets together, hold both face frames flush, see fig. 10A.
Take a 1 1⁄4” screw and insert it behind the face frame, into the side panel of
one cabinet through the other cabinet’s side panel, screwing it tightly together
see figures 10B & 10C. Do this at the top, middle and bottom of the cabinet.
[ fig 10A ]
[ fig 10B ]
[ fig 10C ]
NOTE:
To secure shelf clips to side, use 1/2” silver
screws and screw shelf clips into side panel
Visit Jack’s Design Center, an interactive
SLIDE-LOK Storage System design tool,
which will enable you to design your own
SLIDE-LOK Storage system online
Jack’s Design Center simplifies the process
of designing your own SLIDE-LOK Storage
Solution with features such as user
dimensions, a parts list generator and the
ability to print your SLIDE-LOK creation,
making ordering your next SLIDE-LOK
Storage System easier than ever.
www.slide-lok.com | 800-835-1759
Design Your Own
SLIDE-LOK Storage Solution
