manualshive.com logo in svg

SkyWave IDP 800 Series, Руководство по оборудованию, Страница: 54 / 102

Поделиться
Скачать
SkyWave IDP 800 Series Скачать руководство пользователя страница 54

IDP 800 Terminal Series - Hardware Guide 

T209, Version 01                                                         42                                              © SkyWave Proprietary 

the installation to prevent cable wear and eliminate strain on the 
terminal connector. Damage to the terminal connector interface 
or cable may otherwise result leading to hardware failure. 

 

Mount the remote antenna where it can reach the terminal and has a clear view of 
the sky and satellite. For a mobile installation, this means at the highest point on 
the vehicle or vessel where it has a clear view in all directions. 

 

Do not drill any holes before checking that you have room for the bend radius of 
the antenna cable. For reliable operation, do not go below a bend radius of  
1.3 cm. Measure the bend radius of the cable as shown in Figure 26. 

Figure 26  Remote Antenna Cable Bend Radius 

 

 

Mount on a surface that is free from dirt, grime, water and grease to avoid 
damaging the mounting surface or the vehicle’s paint.  

 

Mount so that the cable end faces the rear of the vehicle.  

4.4  Identify the Fuse Panel Location (optional) 

Follow the steps below if applying external power rather than using the batteries. 

For installation in a truck, the cable from the terminal connects to the truck's fuse panel 
for power. If the terminal is installed on a trailer, an external connection may be made 
with the trailer 7-way panel. The availability of power at the 7-way panel may be limited 
depending on the specific trailer design. Consult the manufacturer for recommendations. 

1.

 

Locate the fuse panel in the truck. The location depends on the type, age, and 
model of the truck. 

2.

 

Identify an un-switched vehicle power source within the fuse panel for terminal 
power.  

3.

 

Ensure that the cable you ordered is of sufficient length to reach from the fuse 
panel to the final mounting location of the terminal. 

4.5  Prepare the Batteries 

The IDP-800 is available specifically configured for rechargeable or non-rechargeable 
batteries. If you ordered a terminal with rechargeable batteries the label on the underside 
of the terminal shows NiMH, while the non-rechargeable battery label shows Li/FeS

2. 

A 

label inside the battery compartment also identifies the cell chemistry.

 

Bend 

Radius 

Correct 

Содержание IDP 800 Series







































































































Отзывы:

Нет отзывов