Skyware Type 123 1.2 Meter Class I and II Antenna System Скачать руководство пользователя страница 2

1

Skyware Global

VERY SMALL APERTURE TERMINAL (VSAT) PRODUCTS

TWELVE (12) MONTH LIMITED WARRANTY

Seller warrants that all Skyware Global manufactured VSAT products are transferred rightfully and with good title; that they are free from 
any lawful security interest or other lien or encumbrance unknown to Buyer. Seller also warrants that for a period of twelve (12) months 
from the date of shipment from Seller’s factory, all its VSAT products shall be free from defects in material and workmanship which arise 

under proper and normal use and service. Buyer’s exclusive remedy hereunder is limited to Seller’s correction (either at its plant or at 
such other place as may be agreed upon between Seller and Buyer) of any such defects by repair or replacement at no cost to Buyer, 

except for the costs of any transportation in connection with the return of the defective VSAT products to be replaced or repaired, and 

the costs to remove and/or reinstall the products, which shall be borne by Buyer. The limited warranty period shall not be extended 

beyond its original term with respect to any part or parts repaired or replaced by seller hereunder.

This warranty shall not apply to VSAT products which (i) have been repaired or altered in any way so as to aff ect stability or 

durability, (ii) have been subject to misuse, negligence or accident, (iii) have been damaged by severe weather conditions such as 

excessive wind, ice, storms, lightning, or other natural occurrences beyond Seller’s control; (iv) have presented damages, defects or 

nonconformances caused by improper shipping, handling or storage, and (v) have not been installed, operated or maintained in 

accordance with Seller’s instructions.

Buyer shall present any claims along with the defective VSAT product(s) to Seller immediately upon failure Non-compliance with any 

part of this warranty procedure may invalidate this warranty in whole or in part.

SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, OTHER THAN AS SPECIFICALLY STATED ABOVE. EXPRESSLY EXCLUDED 

ARE ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING SHALL 

CONSTITUTE ALL OF SELLER’S LIABILITY (EXCEPT AS TO PATENT INFRINGEMENT) WITH RESPECT TO THE VSAT PRODUCTS. IN 

NO EVENT SHALL SELLER BE LIABLE FOR ANY LOSS OF PROFITS OR REVENUE, LOSS OF USE, INTERRUPTION OF BUSINESS, OR 

INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES OF ANY KIND AS A RESULT OF THE USE OF THE 

PRODUCTS MANUFACTURED BY SELLER, WHETHER USED IN ACCORDANCE WITH THE INSTRUCTIONS OR NOT.  UNDER 

NO CIRCUMSTANCES SHALL SELLER’S LIABILITY TO BUYER EXCEED THE ACTUAL SALES PRICE OF THE VSAT PRODUCTS 

HEREUNDER.

In some jurisdictions, Buyer may have other rights under certain statutes that may imply non-excludable warranties. No representative is 

authorized to assume for Seller any other liability in connection with the VSAT products.

DATE   

DESCRIPTION   

 

 

REVISION

08/06   

ECN 9007484   

 

               Rev B

11/07 

 5075515    Rev 

C

05/08 

 5078314    Rev 

D

09/08 

 5075934    Rev 

E

01/10   

654 

 

 

 

 

Rev F                 

04/11   

EC-01063 

 

 

 

Rev G

MANUAL REVISION HISTORY

WARRANTY

DO NOT DISCARD CONTENTS
The product in this packaging was placed in the market after August 13, 2005.  Its components must not be discarded with 
normal municipal or household waste.

Contact your local waste disposal agency for recovery, recycling, or disposal instructions.

Содержание Type 123 1.2 Meter Class I and II Antenna System



















Отзывы: