TROUBLE SHOOTING
If you encounter problems with your fireplace system, the problem may be with either the fireplace itself or with this remote. Review
the fireplace manufacturer’s operation manual to make sure all connections are properly made. Then check the operation of the
remote in the following manner:
Make sure all batteries are correctly installed in the transmitter and receiver. Also check if the batteries are fully charged.
•
Check batteries in transmitter to make sure contacts are touching (+) and (-) ends of battery. Bend metal contacts in for tighter fit.
•
Be sure receiver and transmitter are within 20 to 25-feet operating range.
•
Keep receiver from temperatures exceeding 130 degrees F. Battery life will be shortened if exposed to high temperatures.
•
If receiver is installed in a tightly enclosed metal surrounding, the operating distance will be shortened.
•
Make sure the hand-held transmitter and remote receiver are communicating properly (See LEARNING TRANSMITTER TO RE-
•
CEIVER section).
FCC REQUIREMENTS
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFER-
ENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFI-
CATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
FOR TECHNICAL SERVICE, CALL:
U.S. INQUIRIES
888/672 - 8929 OR 260/459 - 1703
WEB SITE: www.skytechsystem.com
CANADIAN INQUIRIES
877/472 - 3923
MANUFACTURED EXCLUSIVELY FOR SKYTECH II, INC
REV 4/8/11 Page 4
This remote control has a COMMUNICATION –SAFETY function built into its software to ensure the transmitter and receiver are com-
municating normally.
In all operating modes, the transmitter sends an RF signal every fifteen minutes to the receiver indicating that the transmitter is within
the normal operating range of 20-feet. Should the receiver NOT receive this signal, the receiver will begin a 2 hour countdown. If the
receiver does not receive a signal from the transmitter in 2 hours, the receiver will shut off the appliance. The receiver will then emit a
series of rapid “beeps” for a period of 10 seconds. Then after 10 seconds of rapid beeping, the receiver will continue to emit a single
“beep” every 4 seconds until a transmitter
ON
,
OFF
or
MODE
Button is pressed to reset the receiver.
COMMUNICATION - SAFETY - TRANSMITTER - (C/S - T/X)
BATTERY LIFE
Life expectancy of the alkaline batteries in the transmitter and receiver
should be at least 12 months. Check and replace all batteries:
Annually.
•
When operating range becomes reduced.
•
When transmissions are not received by the remote receiver.
•
If the remote receiver batteries measure less than 5.3 volts (all four bat-
•
teries in combination).
If the hand held transmitter batteries measure less than 2.5 volts (both
•
batteries in combination).
LEARNING TRANSMITTER TO RECEIVER
Each transmitter uses a unique security code. It will be necessary to press the LEARN button on the receiver to accept the transmitter
security code upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your dealer or the factory. In
order for the receiver to accept the transmitter security code, be sure the slide button on the receiver is in the REMOTE position; the
receiver will not LEARN if the slide switch is in the ON or OFF position. The LEARN button in located on the front face of the receiver;
inside the small hole labeled LEARN. Using a small screwdriver or end of a paperclip gently press and release the black LEARN button
inside the hole. When you release the LEARN button the receiver will emit an audible “beep”. After the receiver emits the beep press
the transmitter ON button and release. The receiver will emit several beeps indicating that the transmitter’s code has been accepted
into the receiver.
NOTE:
This receiver can hold up to 3 transmitter codes. This is for the times when a second hand held transmitter or a wall transmitter
is required.
TRANSMITTER WALL CLIP
The transmitter can be hung on a wall using the clip provided.
Wood - Drill 1/8’’ pilot holes and install with screws provided.
•
Plaster/Wallboard - Drill 1/4’’ holes, then install with the screws provided.
•
WALL CLIP
SLOT
WALL CLIP
BATTERY
COMPARTMENT
Skytech 1001T/LCD-A
Toll-Free
1-866-667-8454
NorthlineExpress.com
www.NorthlineExpress.com
Toll-Free
1-866-667-8454
NorthlineExpress.com
www.NorthlineExpress.com
