manualshive.com logo in svg

Skyrc Ultimate 10amp x2, Инструкция по эксплуатации

Поделиться
Скачать
Skyrc Ultimate 10amp x2 Скачать руководство пользователя страница 26

Ultimate 200W×2

WARNING AND ERROR MESSAGE

Ultimate  200W×2  incorporates  a  various  functions  of  protective  and  monitoring  the 
system to verify functions and the state of its electronics. In any case of occurring error, 
the screen displays the cause of error that is self-explanatory with audible sound.

Incorrect polarity connected.

Battery connection is interrupted.

Short-circuit of the output termination.

Input voltage wrong.

The voltage of the battery pack has been selected incorrectly! 

The  charger  has  malfunctioned  for  some  reason.  Seek  professional 
advice.

The  voltage  is  lower  than  which  is  set.  Please  check  the  number  of 
cells in the battery pack.

The processor cannot control the feeding current, please repair it.

Wrong  connection  of  the  connector  detected;  please  check  the 
connector and cable.

Voltage  of  one  cell  in  the  battery  pack  is  too  high;  please  check  the 
voltage of each cell.

Voltage  of  one  cell  in  the  battery  pack  is  too  low;  please  check  the 
voltage of each cell.

The  voltage  is  higher  than  which  is  set.  Please  check  the  number  of 
cells in the battery pack.

The internal temperature of the unit goes too high. Cool down the unit.

·

 

25

Содержание Ultimate 10amp x2

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды