L i H V F A S T C H A R G E
1 2 . 0 A O F F - L I N E
L i P o F A S T C H A R G E
1 2 . 0 A O F F - L I N E
L i P o 1 . 0 A 5 0 . 2 1 V
S T O
0 0 0
:
2 3
0 0 0 0 7
L i P o F A S T C H A R G E
1 2 . 0 A O F F - L I N E
L i P o 1 0 . 2 A 3 8 . 1 2 V
B A L
0 0 3
:
0 7
0 1 1 0 5
L i P o B A L A N C E C H G
1 0 . 0 A O F F - L I N E
L i P o B A L A N C E C H G
1 2 . 0 A O F F - L I N E
L i P o F A S T C H A R G E
1 2 . 0 A O F F - L I N E
SWITCH BETWEEN LIPO AND LIHV
Press and hold and at the same time for 5 seconds until the corresponding battery type
appears on the screen.
Note: This function must be used with caution, as charging incorrect type of battery will
damage the battery, or even cause fire or explosion.
PC1260 supports LiPo, terminal voltage of which is 4.2V and LiHV, terminal voltage of which is 4.35V.
How to switch between LiPo and LiHV?
SYNCHRONIZATION
PC1260 charge can be synchronized via data cables. Below illustrates how to charge 8 batteries of the same type.
Make sure all the chargers are set to “OFF-LINE” first. If a certain channel is selected as “MASTER” channel, then the
other channels will be “SLAVE”. The settings on “MASTER” can be applied to all the chargers, which saves your time
significantly.
-
3
-
-
4
-
STORAGE
If a Lithium battery is not used for long time, it's highly recommended to charge or discharge the battery to 3.9V with
STORAGE mode so as to extend the battery Life. If the battery voltage is higher than 3.9V, the charger will discharge the
battery; If the battery voltage less then 3.9V per cell, the charger will charge the battery under STORAGE mode.
Press or to select STORAGE mode
Press , the charging mode will blink
One-Button-Charge Operation
：
3)
Press and hold button for 2 seconds, fast charge starts
3 . 1 8 3 . 1 9 3 . 1 8 V
3 . 2 0 3 . 1 8 3 . 1 9 V
F u e l = 5 2 %
C e l l = 3 . 1 9 V
LCD screen shows battery voltage, current, charge mode, charging time and
recharged capacity.
Parameters Settings
：
4)
Press button, the working mode will be blinking
Press button again, the current option will start blinking; Press or
button to set the charging current within the range of 1.0A-12.0A
Press button again to choose synchronous mode. Press or
button to set “OFF-LINE” or “MASTER”. Either of the channels is MASTER,
the other will automatically change to “SLAVE”. All the settings must be
done through “MASTER”
Press and hold button for 2 seconds to start charging
Press or button to select FAST CHARGE, BALANCE CHARGE or STORAGE
6)
Stop: During the charging process, press button if you like to terminate the charging. Under
Master-Slave mode, any operation must be carried out through the Master channel.
Finish: In charging mode, when the charging process finishes, the screen will be displayed as below:
5)
[ E N D : F I N I S H ]
5 0 . 4 0 V 1 6 5 0 0 m A h
[
T I M E
：
0 1
：
4 5
：
3 6 ]
5 0 . 4 0 V 1 6 5 0 0 m A h
charge current and time
Press and hold , STORAGE mode starts
3 . 1 8 3 . 1 9 3 . 1 8 V
3 . 2 0 3 . 1 8 3 . 1 9 V
Single cell battery voltage
L i P o 1 0 . 2 A 3 8 . 1 2 V
F A S
0 0 3
:
0 7
0 1 1 0 5
L i P o F A S T C H A R G E
1 2 . 0 A O F F - L I N E
L i P o F A S T C H A R G E
1 2 . 0 A O F F - L I N E
L i P o B A L A N C E C H G
1 0 . 0 A O F F - L I N E
Press button to check the battery voltage.
L i P o S T O R A G E
1 2 . 0 A O F F - L I N E
