Thank you for your choice of the SKYRC e6, 100-240V AC balance charger. This unit is simple to use but
its operation does require some knowledge on the part of the user. Please read this entire operating
manual completely and attentively before using this product, as it covers a wide range of information on
operating and safety.
SKYRC e6 Charger is an economic, high quality 100-240V AC balance charger, designed for charging
LiPo and LiFe batteries from 2-6 cells in balance mode. The circuit power is 50W and max charge current
can reach to 5A. There are four kinds of charge current 1A/2A/4A/5A that can be selected. You could
select the proper charge current according to battery capacity.
INSTRUCTION MANUAL
INTRODUCTION
CHARGE PROCEDURES
SKYRC e6 comes with the built in power supply. You can connect the AC power cord to the AC socket
(100-240V AC) directly.
Note: This charger can charge LiPo and LiFe batteries ONLY in balance mode. In this case, you must use
balance board to connect the charger with the battery.
Insert the AC power cord into the charger.
Insert the AC cord into a wall socket (100-240V). All LEDS will light for 1 second and the charge
status LED will flash green which indicates the charger is ready to charge.
Select the battery type LiPo/LiFe by the toggle switch.
Select the proper charging current 1A/2A/4A/5A by the toggle switch.
Connect the battery to the charger main battery lead to battery socket and balance wires to balance
socket.
The charger starts charging. The charge status LED and the cell status LED will glow constant red. If
the battery pack is 2-cell, Cell 1 and Cell 2 LEDs will glow constant red; if the battery pack is 3-cell,
Cell 1, Cell 2 and Cell 3 LEDs will glow constant red; and so on.
During the charging progress, when the charge
status LED glows constant red, the charger is
charging in CC mode; when the charge status
LED glows constant orange, the charger is
charging in CV mode;
When the cell LED is flashing, this cell is
discharging for balancing.
When the battery is fully charged, the charge
status LED will glow constant green.
Unplug the battery from the charger and the
charge status LED will flash green which
indicates the charger is ready to charge
another battery.
Please refer to following steps to charge the battery,
1)
2)
3)
4)
5)
6)
7)
8)
9)
EXPLANATION OF LED STATUS
If the charger encounters a problem, all LEDs will flash red in sequence to alert you to the errors. In this
case, please disconnect the power cord from the wall socket and unplug the battery from the charger.
* Error Message
-
1
-
-
2
-
SPECIFICATION
AC Input
Battery Type
Cell Count
Charge Current
Circuit Power
Current Drain for Balancing
Dimension
Weight
Charger/Cell Status
100-240V
LiPo/LiFe
2-6 cells
1A/2A/4A/5A ± 10%
50W
200mA
82.7x140.5x45.7mm
310g
SK-100052
This diagram shows the correct way to connect your
battery to the e6 charger while charging in balance
mode.
Failure to connect as shown in this diagram will
damage this charger.
The main battery leads must be connected along with
the balance lead connector as shown before charging
your battery.
CAUTION:
LED flashes green
LED glows constant red
LED glows constant orange
LED glows constant green.
LED glows constant red.
LED flashes red
The charger is ready to charge.
The charger is charging in CC mode.
The charger is charging in CV mode.
The charging process finishes.
The cell is charging.
The cell is discharging.
Charge Status LED
Cell Status LED
CONNECTION DIAGRAM
Battery Type Switch
Cell 3 LED Indicator
Cell 2 LED Indicator
Cell 1 LED Indicator
Cell 6 LED Indicator
Cell 5 LED Indicator
Cell 4 LED Indicator
Charge Current Switch
Charge Status LED Indicator
Battery
Socket
Balance
Socket
100-240V
Power
Jack
Charger
Balance
Adaptor
Battery
10)
