Ⓐ Activate your m2500 system
1. Get the system serial number from the retail box (side) or ISI-2000 (bottom)
2.1. Using the mazu app…
a)
Connect your iPad to the Internet. Download mazu
from the Apple App Store.
b)
Stay connected to the Internet. Launch mazu and follow the instructions
to Register
and Activate your m2500 system.
c)
Configure your email app
as described in mazu Share. The Incoming and Outgoing Servers are
mazu.skymate.com
Your Activation CREDENTIALS (e.g. username, password) are saved in mazu Settings
General.
2.2. Without the mazu app…
a)
Connect your device to the Internet. Open a browser
and go to
https://www.skymate.com/mseries
b)
Follow the instructions
to Activate.
3. An email is sent to you when you Activate which includes all your mSeries Credentials.
Ⓑ
Install your m2500 system
1. Install the Base Unit (ISI-2000)
a)
Select a dry location
for the installation.
b)
Secure the mounting bracket
with the double-sided tape (already on the bracket) and/or using
the screws provided.
Slide the Base Unit onto the bracket
until it clicks in place.
c)
Connect the Power Cable
to the boat battery.
Connect the black wire to the negative(-) and the red
wire to the positive (+).
An in-line fuse is not required.
Note: Do not connect the Power Cable to the Base Unit until Step 4.
2. Install the Keypad (KPD-100)
a)
Select a panel location
for the Keypad. It can be mounted using the tape on the back of it or be bolted.
b) If the Keypad is to be bolted, then
drill the holes in the panel
using the template provided. Secure it with
the supplied wing nuts.
c)
Connect the Keypad
to the Base Unit.
Surface Mount
Through Hole
3. Install the Smart Antenna (IGT-2100)
a) Decide whether you want the Smart Antenna to be
flush mounted
or attached to a standard
1-inch-14 mount.
Out-of-the-box, it is configured for the standard mount. The 1-inch-14 mount is not included.
b1) For the standard mount,
slightly loosen the four bolts
so that the 1-inch-14 adapter can be rotated.
Hand tighten the adapter
to mount,
orient
the antenna;
and then
re-tighten the four bolts.
b2) For the flush mount,
remove the four bolts,
boot and threaded adapter. Drill holes
for the four
mounting screws and the cable.
Secure it
to the deck with the screws and rubber washers supplied.
c)
Insert the four screw caps
provided into the bolt/screw recesses.
d)
Connect the Smart Antenna
to the Base Unit. The cable should not be cut. Contact SkyMate for cable extension.
Flush Mount
Standard Mount
4. Power ON your m2500 system
a) Connect the Power Cable to the Base Unit. It will turn ON and self-test. Observe the front panel
indicators and Keypad, as this is an indication of proper operation.
i. Within 3-10 minutes, all LED indicators on the Base Unit will be green.
ii. On the Keypad, only the SOS buttons will remain ON (dim).
b) With all LEDs green, the m2500 system has successfully powered ON and is ready for your
mazu iPad to Wi-Fi connect to it to complete your Activation.
Note:
The Base Unit LED status descriptions are in mazu Settings > Base System > ISI-2000.
Ⓒ Test your m2500 system
1. Wi-Fi connect your device or mazu iPad to the Base Unit
a) If you have the mazu app, launch it.
b) If you don’t have mazu, open a browser and enter
mseries.online
to bring up your mSeries web interface.
Enter your
username
and
password
from Activation.
2. Send/Receive email
a) Open your email app or mSeries web interface and send a test email to
(this email will be echoed back to you).
b) Within a few minutes, the Keypad message waiting light will go ON.
c) Confirm that you received the test email response.
3. If you need to change the configuration of your mSeries system...
a)
Connect to the Internet.
b) Go to
mazu Settings
(SKYMATE ACCOUNT) or go the
https://www.skymate.com/mazu
and login.
