6. ERASING TC TRANSMITTERS FROM THE
ON/OFF CONTROL
You may erase a transmitter from the ON/OFF Control, but you cannot
erase a specific device directly, you must erase all the wireless devices,
then program the ones you want to keep. Follow the instructions below
to erase programmed TC transmitters.
1. Power off the lighting receiver. (Switch off the wall switch)
2. Press the PROG button on the back of the TC transmitter, the front LED
will be on.
3. Press and hold the programmed button on the TC transmitter for at
least 2 seconds, the red LED will flash quickly. Do not release this
button until step 5.
4. Power up the ON/OFF Control (Switch on the wall switch), you will hear
a beep.
5. You may release the button on the transmitter.
6. When the button is release, the ON/OFF Control will beep, indicating
you have successfully erased all the devices from the ON/OFF Control.
To erase other transmitters / sensors, please refer to the instructions of
the transmitters / sensors.
Input Voltage: 120VAC, 60Hz
Maximum Load: 600W at 120VAC
Operating Frequency: 318MHz
Range: Up to 500 feet in open area
Standby Current: 3mA
Minimum Load: 10W
Operational Temperature: -4° F - 140° F
(-20° C - 60° C)
Humidity: 5%-95%
7. TECHNICAL SPECIFICATIONS
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Z698
Patent Pending
©2010 SKYLINK GROUP
5. ZONE OPERATION (AVAILABLE WITH 10-BUTTON /
14-BUTTON DELUXE TRANSMITTER ONLY)
4. ON / OFF OPERATION (CONT)
To toggle a receiver between these two states, re-program a transmitter
twice consecutively to the receiver. Referring to Section 3, repeat the
programming steps twice consecutively with a transmitter that is already
programmed, the receiver will change state.
Note: When used with an optional Motion Sensor ID-318, this ON/OFF
Control can operate under countdown timer mode.
Note: The two optional Power-On states are also applicable to loads
other than lights.
V2.0
8. FCC
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
10. CUSTOMER SERVICE
11. ACCESSORIES
The Skylink
System consists of many other devices such as
SkylinkHome Remotes, Motion Sensor, ON/OFF Wall Switch, Wall
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,
ON/OFF Control, Smart Button Garage Door Control, etc. Please visit
Skylink website at www.skylinkhome.com for more information.
TM
Home
TM
TM
9. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
2. Power On - Light Off:
1) With the wall switch, you have to use this special sequence to turn on
the light: first, switch on, second, switch off then switch on immediately
(within 2 seconds), the light will be turned on.
2) After a power outage and electricity comes back, the light will be off
under most of the circumstances.
An optional deluxe remote is needed for zone operation. A Zone Command
allows you to operate multiple lights altogether in the same zone.
A zone command must first be programmed to the receiver before zone
operation. To program a zone command, please refer to the user's
instructions of the deluxe remote.
Zone Operation - On / Off
To turn on or off a zone, hold [ ] or [ ] until the red LED flashes
three times and keeps on, then release the held button and press the
zone number.
For example:
Hold [ ] until the red LED flashes three times and keeps on, then
release [ ] and press [1], all lights in zone 1 will be turned on.
Hold [ ] until the red LED flashes three times and keeps on, then
release [ ] and press [1], all lights in zone 1 will be turned off.
Note: The Zone Operation is also applicable to loads other than lights.
If you would like to
-
find out the up-to-date specifications
-
know more about features and applications
-
download documents, i.e. user’s instructions
-
order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
