The sensor must be programmed to the Household Alert
®
Long
Range
Receiver before they can communication. You may program the sensor
to one of the 4 zones. Follow the instructions below;
1.
Plug in an AC adapter to the receiver.
2.
Power up the Receiver unit. The green LED will be on indicating it
is turn on.
3.
Open the back cover and there is a learn button. Press and hold
this learn button for 5 seconds, until both green LED and zone 1
red LED
You may now release the learn button.
4.
If you would like to program the sensor to zone 1, activate the
sensor while the zone 1 red LED is
Activate the Sensor
by separating the magnetic contact from the sensor.
5.
If you would like to program the sensor to other zones, press the
learn button again, until the red LED
at the zone you want
to program the sensor to, then activate the sensor.
6.
Once the sensor is programmed, the green LED will be steadily on
and none of the red zone LEDs will be on.
Note: Each zone can program up to 4 sensors. If you try to program a
sensor into a zone, the
programmed sensor will be erased.
Plug in the adapter to the receiver
4. PROGRAMMING WINDOW/DOOR SENSOR
Learn Button
Separate the magnet from
the sensor, Receiver zone LED
stops
.
After learning the sensor to the Receiver unit, you may test the com-
munication by placing the magnet beside the sensor (where the red
marking is) and remove the magnet from the sensor.
When the magnetic is closed, the
receiver will not beep.
When the magnetic contact is broken (open),
the receiver will beep and zone LED will
.
1)
Zone LED of this sensor will
h.
2)
Beeping according to the zone number [Operating mode is set to
“Alert”]. 1 beep for zone 1, 2 beeps for zone 2 and etc, until the
magnetic contact is closed.
You cannot erase a
sensor. You must erase all sensors from
the receiver, then program the ones you would like to keep. To erase all
the sensors from the receiver:
1. Remove the adapter from the receiver.
2. Open the back cover, press and hold the learn button. Do not release
the learn button until step 4.
3. While holding onto the learn button, plug in the adapter to the receiver.
4. You may release the learn button when the LEDs on the receiver are
on.
5. You have erased all sensors from the receiver.
5. WINDOW/DOOR SENSOR INSTALLATION
Sensor
Sensor
Magnet
Magnet
"Red Marking"
on the side
"Red Marking"
on the side
The transmitters should be mounted on the door frame or window frame
by double sided tape. The magnet should be mounted on the door or
window by either double sided tape or screws. Make sure the magnet is
aligned with the red marking on the transmitter. If the surface of the frame
is
enough, double-sided foam tape is
otherwise, it is
recommended to screw the mounting plate to the frame, then apply
double sided tape. After mounting the sensor, if the Skylink logo is
inverted, remove the front cover and rotate it so the Skylink logo is in the
upright position.
Mounting plate
and screws (optional)
Double-sided
foam tape
Sensor
6. OPERATION
There are 3 di
operating modes for the Household Alert
®
Long
Range Receiver.
1) Alert - Beeps when a sensor is activated, corresponding zone LED
will also
.
2) Alarm - Sounds an alarm when a sensor is activated, corresponding
zone LED will also
.
3)
- No audio sound will be emitted when sensor is activated.
Zone LED will
to indicate the activated
sensor.
To select the operating mode, place the
slide switch on the side at the desired setting:
OFF - No Audio
ALERT - Alert Mode
ALARM - Alarm Mode
Alert
When motion is detected in the monitored area, the sensor will send a
signal to the receiver. It will beep and the corresponding zone red LED
will
for 15 seconds.
If the sensor is set to zone 1, zone 1 red LED on the receiver will
and the receiver will emit a continuous “single beep”, i.e. “beep” pause,
“beep”, pause….. etc.
If the sensor is set to zone 4, zone 4 red LED will
and the receiver
will emit a continuous “4 beeps”, i.e. “beep beep beep beep” pause
“beep beep beep beep” pause ……etc.
By the number of beeps emitted by the receiver, user can identify which
zone is triggered.
Test Sensor
Erasing a sensor
Operation
Page 2 of 3
