When chime mode is enabled
and your Skylink Alarm System
is disarmed, the Main Console will
beep every time a sensor gets
triggered.
When alert mode is enabled
and your Skylink Alarm System
is disarmed, the Main Console will
beep continously when a window/
door is opened or motion is detected
until the sensor is deactivated.
Chime Mode
Alert Mode
14. Enable Chime or Alert Mode
23. Warranty / Customer Service
20. Sensor Failure/Battery Indication
21. FAQ
This product is guaranteed to be free of defects in materials and
workmanship for 1 year from the date of purchase. If this product
is defective, call 1-800-304-1187 for repair or replacement parts.
Guarantee does not include normal wear and tear or batteries.
If you have any questions, problems or missing parts, please call:
Skylink Customer Support
1-800-304-1187
9:00am – 5:00pm EST, Monday-Friday.
Or e-mail us at [email protected]
www.skylinkhome.com
P/N:101Y184
- You must program the sensor or keypad to zone 1 of the main
unit before they can work together.
- Ensure to input the correct password on the Keypad.
- Ensure to input the correct password if enable the password
feature in keychain remote.
The Main Console does not respond to the sensor, keychain remote
or Keypad Control?
- You must erase all the sensors/remotes in that zone and then
program the remote you want to keep.
Can I erase just one sensor or remote from a zone?
- You need to test each remote/keypad/sensor individually.
I have multiple remotes in a zone and the zone LED keep flashing
that is a remote failure, how do I know which sensor/remote
is having the problem?
- It is recommended to power up the control panel with AC adapter.
Install batteries to the Control Panel so it can continue to operate
during power failure.
Can I only use battery to power up the Control Panel?
If the signal is lost between the sensor and the Main Console,
or if the battery in the sensor is low, the zone LED light will
start blinking fast
.
Take the following steps to troubleshoot the problem:
1. Check if the sensor is located where it should be, and whether
there is any physical damage to the sensor.
2. If the failed sensor is not physically damaged, try to activate the
sensor and see if the Main Console reacts to the activation.
3. If not, try to remove the sensor from its location, and bring it
closer to Main Console and then activate the sensor. It is possible
that the sensor is installed too far from the Main Console and it
cannot establish a steady communication with the Main Console.
If this is the case, please install the sensor closer to the
Main Console.
4. Replace the battery of the sensor in that zone if the Main Console
does not respond even when the sensor is near the Main Console.
NOTE: If you have multiple sensors in a zone, you may test the function
of each sensor to identify which sensor is having a problem.
1. Slide the switch at the back of the Main Console to enable Chime
or Alert Mode.
15. Alert Notification
The motion sensor can be mounted with a double
sided tape or screws in a corner, straight wall, ceiling or
stand freely by itself.
22. Erasing the Sensors/Remote from the Main Console
1. Remove the power adapter from the Main Console.
2. Press and hold the Learn Button and plug in the power
adapter back in the Main Console.
3. Release the learn button when the red LED are flashing on
the Main Console.
4. You have successfully erased all sensors and remotes from the
Main Console.
NOTE: To erase any sensors or remote from the Main Console, you need
reset the Main Console and learn the sensors/remotes you wish to keep.
LED
AC Adapter
Learn Button
Arm Home
Arm Away
13. Operation of Alarm System
1. Arm your alarm system by
pressing the “Arm Away” or
“Arm Home” button on
the Security Keychain Remote or
by entering your PIN number
followed by the “Arm Home” or
“Arm Away” button on the
Security Keypad Console.
2. When a sensor get triggered,
the main console will sound a
siren and the corresponding
zone LED will flash for 3 minutes.
Arm Away
Arm Home
3. Press the “Disarm Button” on
your Keychain Remote or enter
the PIN number and press
the “Disarm Button on the
Keypad Console to deactivate the
alarm system.
12. Install the Motion Sensor
Place the sensor in the appropriate location:
ZONE 1 SENSORS -
1 Beep , Pause , 1 Beep , Pause ... etc.
ZONE 2 SENSORS
- 2 Beep , Pause , 2 Beep , Pause ... etc.
ZONE 3 SENSORS -
3 Beep , Pause , 3 Beep , Pause ... etc.
ZONE 4 SENSORS -
4 Beep , Pause , 4 Beep , Pause ... etc.
When the Alert Mode is activated, you can identify the
zone number by the number of beeps.
The beeping will continue until the sensor is deactivated. When the
Main Console receives a signal from the motion sensor, the Main
Console will beep and the LED will flash on the corresponding zone
for 15 seconds.
Press the
MUTE
button if you want to temporarily disable the
beeping sound.
Disarm
Disarm
17. Program W/D Sensor to Main Console
1. Press and hold the “Learn”
button for 3 seconds, until
the Zone 1 red LED flash.
2. Zone 1 is selected. Press the
learn button to select the Zone
you want to program the sensor.
3. Activate the Sensor
by separating the magnetic
contact of the sensor.
4. Once the sensor is programmed,
the Main Console will beep once and
the corresponding zone red LED
will be off.
18. Program Motion Sensor to Main Console
1. Press and hold the “Learn”
button for 3 seconds, until
the Zone 1 red LED flash.
2. Zone 1 is selected. Press the
learn button to select the Zone
you want to program the sensor.
3. Open the Motion Sensor
cover with a coin and press
the learn button.
4. Once the sensor is programmed,
the Main Console will beep once
and the corresponding zone red
LED will be off.
19. Zone Settings
16. Program Security Remote/Keypad Console
1. Press and hold the “Learn”
button for 3 seconds, until
the Zone 1 LED is flash.
3. Once the Security Keychain
Remote or Keypad Console is
programmed, the Main Console
will beep once and the
corresponding zone LED will be
off.
2. Press any button to program the
Security Keychain Remote or enter
the PIN number followed by the
“Disarm Button” to program
the Security Keypad Console.
NOTE: The Keychain Remote must be programmed in Zone 1. You can
program up to 4 Remotes or Keypads with the Main Console.
Refer to the chart below for the 2 zone operation modes. The unit
is currently set at Default Zone Setting Mode.
Change between Default Zone and All Alert Zone Mode:
1. Power up the Main Console.
2. Press and hold the “Learn” and “Mute” button simultaneously
for 5 seconds, until you hear the beep.
3. If you hear one beep, you are in “All Alert Zone Setting” and if
you hear 2 beeps, you are in “Default Zone Setting”.
4. Release both button.
Zone Setting
Default Zone Setting
Zone
Zone
1 & 2
Special Zone Setting
Suggestion Application
Zone 3
Zone 4
Alert when disarmed,
Alarm when armed.
Alert when disarmed,
Alarm when armed.
Alert when disarmed,
Alarm when armed.
Alert when disarmed,
Alarm when armed
.
No alert when disarmed,
but will alarm when armed.
Alert Only,
No Alarm.
For outdoor sensor.
Indoor motion sensor in
a high traffice area.
Most sensor, except for sensors
in outdoor or high traffic area
.
NOTE: You can program up to 4 sensors in each Zone.
NOTE: You can program up to 4 sensors in each Zone.
Repeat the above steps to change between 2 operation modes.