background image

Disassembly Guide    

October 5, 2021 

 

 

17 

6

 

WEEE Annex VII parts 

LCDs TV using Light Emitting Diode (LED). 

 

 

Requirements according to ANNEX VII of DIRECTIVE 2012/19/EU  

on waste electrical and electronic equipment (WEEE) 

 

Materials and components with hazardous content 

LCDs may contain hazardous substances like Lead and Brominated Flame Retardants (BFRs) which are 
covered by exemptions under the RoHS directive. However, the majority is present in the printed circuit 
boards assembly. To reduce emissions as much as possible, a complete disposal of the old appliance is 
required. This treatment may only be performed in authorized handling plants. 
 

 

 

Substance 

Relevant 

Refer to 

subassembly 

a) 

Mercury containing components, such as switches or backlighting lamps. 

N/A 

N/A 

b) 

Batteries. 

 

Remote control 

c) 

Printed circuit boards of mobile phones generally, and of other devices if 
the surface of the printed circuit board is greater than 10 square 
centimetres. 

 

4, 9, 11, 

20, 24, 30 

d) 

Toner cartridges, liquid, and paste, as well as colour toner. 

N/A 

N/A 

e) 

Plastic containing brominated flame retardants. 

N/A 

N/A 

f) 

Asbestos waste and components which contain asbestos. 

N/A 

N/A 

g) 

Cathode ray tubes. 

N/A 

N/A 

h) 

Chlorofluorocarbons (CFC), hydrochlorofluorocarbons (HCFC) or 
hydrofluorocarbons (HFC), hydrocarbons (HC). 

N/A 

N/A 

i) 

Gas discharge lamps. 

N/A 

N/A 

j) 

Liquid crystal displays (together with their casing where appropriate) of a 
surface greater than 100 square centimetres and all those backlit with gas 
discharge lamps. 

 

k) 

External electric cables. 

 

External cables 

l) 

Components containing refractory ceramic fibres as described in 
Commission Directive 97/69/EC of 5 December 1997 adapting to technical 
progress for the 23rd time Council Directive 67/548/EEC on the 
approximation of the laws, regulations and administrative provisions 
relating to the classification, packaging and labelling of dangerous 
substance. 

N/A 

N/A 

m) 

Components containing radioactive substances, with the exception of 
components that are below the exemption thresholds set in Article 3 of 
and Annex I to Council Directive 96/29/Euratom of 13 May 1996 laying 
down basic safety standards for the protection of the health of workers 
and the general public against the dangers arising from ionizing radiation. 

N/A 

N/A 

n) 

Electrolyte capacitors containing substances of concern (height > 25 mm, 
diameter > 25 mm or proportionately similar volume)  
These substances, mixtures and components shall be disposed of or 
recovered in compliance with Directive 2008/98/EC. 

 

11 

o) 

Cathode ray tubes: the fluorescent coating must be removed. 

N/A 

N/A 

p) 

Equipment containing gases that are ozone depleting or have a global 
warming potential (GWP) above 15, such as those contained in foams and 
refrigeration circuits: the gases must be properly extracted and properly 
treated. Ozone-depleting gases must be treated in accordance with 
Regulation (EC) No 1005/2009. 

N/A 

N/A 

q) 

Gas discharge lamps: the mercury shall be removed. 

N/A 

N/A 

Содержание Glass LT043-f1-zzz






















Отзывы: