background image

16

Warranty

SKUTT CERAMIC PRODUCTS, INC. warrants this product to be free from defects in materials and 

workmanship for two full years from the date of the first retail purchase from an authorized Skutt 

dealer.

What Skutt will Do

Skutt will repair or replace, at its expense, any defective part upon return, freight prepaid, to any 

authorized Skutt Service center.

What is Not Covered

.  

This warranty does not cover (1) any defect not reported to an authorized Skutt dealer or distributor 

within 10 days of discovery;  (2) Type K Thermocouples; (3) any damage caused by overfiring; (4) 

products subjected to abnormal strain, freight damage, neglect, abuse, improper storage, failure 

to follow instructions, or products altered from factory standard condition; (5) products whose 

identification number has been changed; (6) failures of, or failures caused by, parts or accessories 

not manufactured or supplied by Skutt Ceramic Products; (7) kilns used for purposes other than firing 

glass materials; (8) elements used in the process of melting glass in a crucible kiln or otherwised 

exposed to long hold times at high temperatures.

Other limitations.

  ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING 

PROPERTY DAMAGE, LOST PROFITS, LOSS OF USE, OR OTHER ECONOMIC LOSS, ARE EXCLUDED 

TO THE FULL EXTENT PERMITTED BY STATE LAW.  Some states do not allow the exclusion of 

incidental or consequential damages, so the above exclusion may not apply to you.  ANY IMPLIED 

WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS 

FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED 

WARRANTY.  Some states do not allow limitations on how long an implied warranty lasts, so the above 

limitation may not apply to you.  Dealers are not authorized to modify this Warranty or to make any 

additional commitments.  Skutt will not be responsible for promises not contained in this Warranty.  

State Law Rights

.  This Warranty gives you specific legal rights, and you may also have other rights 

which vary from state to state.

6441 S.E. JOHNSON CREEK BLVD, PORTLAND, OREGON 97206     (503) 774-6000

How to Request Warranty Service

All repair work must be authorized, either by Skutt, or by an authorized Skutt Distributor before the 

work is done. If you believe your kiln is going to require warranty servicing, the first step is to call the 

Distributor from whom you purchased the kiln. If they are unable to provide or coordinate service, call 

Skutt Ceramic Products and ask for our Technical Service Department. 503-774-6000

Skutt has one of the most extensive networks of Distributors in the country. However, not all areas 

have a trained kiln technician. We realize that re-packaging and shipping your kiln is not a realistic op-

tion for most of our customers. Many of our Distributors have trained kiln technicians either on staff or 

with which they contract. Often times these technicians will travel to your business or home to do the 

repair. Skutt will pay them for their time on the job. It is your responsibility to pay them for their travel 

time to and from your location. 

PLEASE REGISTER YOUR WARRANTY AT WWW.SKUTT.COM

under the “Contact Us” tab to streamline future warranty requests. 

You will need your SERIAL NUMBER, MODEL NAME, VOLTAGE, and PHASE. 

All of this information can be found on the SERIAL PLATE,

which is located on the back of the kiln. 

Содержание Micro Scarab

















Отзывы: