background image

AL-500P-II 7 

12/15/1999

 

 

Figure 3 – Option Select (DIP) Switch Diagram 

 

A switch is “On” when it is pointing in the direction of the arrow 
AWAY FROM the switch numbers, and “Off” when it is pointing 
TOWARDS the switch numbers. 
 
The diagram above is for illustrative purposes only—your actual 
switch settings will vary. 
 
Switch settings are read only at the moment power is turned on. 
Therefore, any changes made to the switch settings while power 
is on do not take effect until the power is recycled. 

 

Switch # 

Option 

Possible Values 

1 Message 

play 

On = Trigger only 
Off = Continuous play 

2-3 Bandwidth 

2 Off, 3 Off = 3.5KHz/34KBps 
2 On, 3 Off = 7.0KHz/69KBps 
2 Off, 3 On = 7.0E KHz/92KBps 
2 On, 3 On = 7.0E KHz/92KBps 

Tape load preview 

On = Enabled 
Off = Disabled 

5-8 Not 

used 

Table 2 – Option Select Switches 

 
 

Message memory

  - AutoLoader 500P is available with 4, 8, 16 or 32 

minutes (@3.5 KHz Bandwidth) of message memory.  The system 
automatically senses the amount of message memory and adjusts the 
message length accordingly. 

 

Memory Size 

4 Min. 

8 Min. 

16 Min. 

32 Min. 

Bandwidth

Sample 

Rate 

4 Min. 

8 Min.

16 Min.

32 Min.

3.5 KHz

34KBps

2 Min. 

4 Min.

8 Min.

16 Min.

7.0 KHz

69 KBps

90 Sec. 

3 Min.

6 Min.

12 Min.

7.0E KHz

92 KBps

Table 3 – Message Memory Table 

 

Example

Switch 1:  Continuous play 
Switches 2&3:  7KHz bandwidth - 69KBps
Switch 4:  Tape preview disabled

 

Switch Knob

Содержание AL-500P-II













Отзывы: