manualshive.com logo in svg

Skoda Rapid NH 2014, Руководство по ремонту


Поделиться
Скачать
background image

– Loosen the seat upholstery -2- from the seat rack -1- and re‐

move the seat upholstery.

Installing
– The installation occurs in reverse order.

Note

Before the installation, check all the fixing elements for damage,

if necessary replace.

1.4

Removing and installing the operating

lever of the seat height adjustment

Removing
– Remove front seat

⇒ “1.1 Removing and installing front seat”, page 286

 .

– Remove the seat trim panel on the rail side (seat with height

adjustment)

⇒ “1.3 Removing and installing the seat upholstery on the rail

side (seat with height adjustment)”, page 289

 .

– Release the screws -1- (4.5 Nm) and remove the operating

lever -2-.

Installing
– The installation occurs in reverse order.

1.5

Removing and installing the seat trim

panel on the tunnel side

Removing
– Remove front seat

⇒ “1.1 Removing and installing front seat”, page 286

 .

– Remove the front belt buckle

⇒ “1.3 Removing and installing the front seat belt buckle”, page

214

 .

– Remove screw -1- (1 Nm).
– Loosen the seat upholstery -2- from the supports in the seat

rack -3- and remove the seat upholstery.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Front seats    

291

Содержание Rapid NH 2014
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid NH 2014

Kargo Master 40640 Assembly Manual preview
40640
Бренд: Kargo Master Страницы: 5
ZAPTEC Go Instruction Manual preview
Go
Бренд: ZAPTEC Страницы: 240
Feniex AM600 Instruction Manual preview
AM600
Бренд: Feniex Страницы: 6
JASTEC von-S2 Instruction Manual preview
von-S2
Бренд: JASTEC Страницы: 12
Honda HRM3000 User Manual preview
HRM3000
Бренд: Honda Страницы: 73
Calix M5T 187A Assembly Instructions preview
M5T 187A
Бренд: Calix Страницы: 5
Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Бренд: Horn Tools Страницы: 6
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Бренд: Romik Страницы: 6
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Бренд: Axxess Страницы: 8
Mazda 1989 323 Manual preview
1989 323
Бренд: Mazda Страницы: 13
Cadillac 2004 ESCALADE Customer Convenience/Personalization Manual preview
2004 ESCALADE
Бренд: Cadillac Страницы: 20
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Бренд: Acura Страницы: 6
Gator GRM430EM User Manual preview
GRM430EM
Бренд: Gator Страницы: 6
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Бренд: Mitsubishi Страницы: 362

Бренды по названию

Популярные бренды

Загрузить еще бренды