Skoda Rapid NH 2014 страница 180 Скачать руководство пользователя

Страница: 180 / 319

1 - Rear bumper
2 - Monte Carlo rear spoiler
3 - Glue sealing material

3.2

Removing and installing the cover

Note

♦

The ambient temperature as well as the temperature of the

parts must be at least 18 °C, maximum 30 °C.

♦

After glueing the tuning parts, the vehicle must remain in a

warm room for at least 3 hours.

♦

Before glueing, all of the adhesive surfaces must be de‐

greased with good quality - the quality of the glued joint de‐

pends upon this!

Adhesive mate‐

rials

Part number

Purpose, application range

Denomination, manufacturer,

comment

PUR - adhesive D 172 090 A2

Glue tuning parts to the body.

Caution: Comply with the

manufacturer's handling in‐

structions. Filling: 310 ml

Glass/paint pri‐

mer for plastic

parts

D 822 150 A1

Prepare the plastic surfaces before

gluing to improve adhesion of the plas‐

tic

Filling: 10 ml

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

172

Rep. gr.66 - Exterior equipment

Содержание Rapid NH 2014
































































































































































































































































































































Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды

Skoda Rapid NH 2014, Руководство по ремонту

Результаты поиска

Содержание Rapid NH 2014

Отзывы:

Похожие инструкции для Rapid NH 2014

Бренды по названию

Популярные бренды