SkinFab treatments
Phase 1: Cleansing (Positive ions + Infrared ray + Micro vibration massage)
Phase 1 deeply cleans skin pores, removing excess sebum deposits, dirt, debris and impurities,
hydrates the skin and kills bacteria.
Firstly removing any trace of makeup with cleansing lotion. When
doing the facial cleanse you need to apply an electronegativity
conductivity facial cleanser on to the skin. Usually facial cleansers
have surfactant which is in negative polarity so make sure you buy a
cleanser that has. Then, the dirt will dissolve in the facial cleanser
turning impurities into negative polarity. The SkinFab device on phase
1 produces positive polarity ions which then attracts the negative
polarity dirt, this is due to opposite charges attracting each other like
the north and south poles of a magnet. Due to this the SkinFab then
draws out the impurity from deep within skin pores.
Phase 2: Massage (Positive and negative ions + Infrared ray +
Micro vibration m Impulse micro current)
Phase 2 relaxes the skin and balances the skin’s pH by appropriately
stimulating positive and negative ions alternately that penetrate deep
within the skin. This phase makes your skin more elastic and toned
and it prepares your skin for phase 3 nutrient. The beneficial energy
of the negative charged ions also strengthens the skins cellular
resistance to aging (Anti aging).
Apply massage products on your skin face and, in case you need it,
on your neck. Choose phase 2 massage.
Switch the SkinFab device on, choose your age, regulate the intensity and go on with phase 1
cleansing. Connecting the sensors on either side of the SkinFab with your hand creates a circuit that
then allows the SkinFab to emanate ions, this kills over 99% of the yellow staphylococci, and other
harmful bacteria within your skin, for instance acne bacteria.
Massage your face slowly with the device in rotating movements from the inside to the outside, from
bottom to top until the programme stops automatically.
Rinse your face with water and pat your skin dry with a warm towel.
Massage your face slowly with the device in rotating movements from inside to the outside, from
bottom to top, until the programme stops automatically.
Phase 3 penetrates water-soluble treatment products deep into the
skin, stabilises skin biological structure, increasing skin elasticity and
giving it tone.
The skin tissue is composed of epidermis as the outer layer, dermis,
and hypodermis that contains fat. Skin cell renews every 28 days.
The protective membrane in the epidermis layer can isolate skin from
harmful environment and substances so as to protect it, but at the
same time, it hinders skin from absorbing nutritious substances.
Therefore, to enhance skin's absorption of nutrition, high-tech
ion-guided technique was developed firstly for use in professional
beauty salons. Now with SkinFab you have the luxury of this same
technology for use in the home.
The principle of the high-tech ion-guided technique is that the current connects the device and
human body to make a complete circuit loop, which drives your skincare solution through the
protective membrane of the skin to reach the deep layer of the skin directly. Meanwhile in the
guiding process, the current stimulates the skin with its thorough massage, which accelerates the
development of skin tissues. Apply a water-based serum, essence or vitamin facial mask on your
face. Choose phase 3 nutrient then massage your face slowly with the intelligent SkinFab beauty
device from the inside to the outside, from bottom to top, until the programme stops automatically.
Phase 4: Lifting (Positive and negative ions + Infrared ray +
Impulse micro current)
Phase 4 reduces face muscles tension, enhances the connective
tissue, reduces deep and fine wrinkles and keeps skin tight, toned
and lifted. The SkinFab appropriately stimulates positive and
negative ions alternately at a different rate to phase 3 that penetrate
deeper within the skin.
Select phase 4 lifting. Move the intelligent SkinFab beauty device
slowly from the inside to the outside of your face, from bottom to top.
Focus on one point for 5-10 seconds. The distance between two
adjacent points is suggested to be two centimetres.
Phase 3: Nutrient (Negative ions + Infrared ray + Micro vibration m Impulse micro current)