Skil PWRCore 20 PM4912E-00, Руководство пользователя

Страница: 8 / 12

8
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always switch off the tool, remove battery pack, and
ensure that all moving parts have come to a complete
standstill
• Always keep tool clean
• Clean the mower after each use with a hand brush and
a soft cloth
! do not use water (especially no high-pressure
sprays)
- remove compacted grass cuttings from the blade area
with a wooden or plastic implement
• Storage
o
- for saving substantial storage space fold the tool
handle and store the tool as illustrated; empty grass
box first
! ensure that the handle cord is not trapped when
folding/unfolding the tool handle (do not drop the
handle)
-
do not place other objects on top of the mower when
stored
• Regularly check the grass box for wear or damage
• Regularly check for worn or damaged blades and bolts
and have them replaced in sets to preserve balance
• Replacing the cutting blade
p
! remove safety key and batteries from tool and
remove grass box
q
b
! wear protective gloves
-
turn the mower upside down
- remove/mount the cutting blade with a spanner 23 as
illustrated
! only use replacement cutting blades of the
correct type (SKIL accessory SMB1700, marked
LERA430X)
- thoroughly clean the shaft area and the underside of
the tool before mounting the cutting blade
TROUBLESHOOTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! always switch off the tool, remove battery packs,
safety key, and ensure that all moving parts have
come to a complete standstill

Tool does not operate
- empty battery -> charge battery
- safety key missing -> check correct installation of safety
key
e
- telescopic handle problem -> fully extend handle and
lock the levers
q
c
- hot battery -> let battery cool down
- cutting blades jammed -> clear jammed material
-
grass too high -> increase cutting height and tilt tool
- internal fault -> contact dealer/service station

Tool operates intermittently
- internal wiring defective -> contact dealer/service
station

Tool leaves ragged finish or motor labours
- cutting height cut too low -> increase cutting height
- cutting blade blunt -> replace cutting blade
- underside of tool badly clogged -> clean tool
• Adjusting height of tool handle
r
I = High
II = Medium
III = Low
• Adjusting cutting height (25-75 mm)
t
-
adjust central handle by putting it in slot for desired
cutting height. 1 = 25mm, 2 = 35mm, 3 = 45mm, 4 =
55mm, 5 = 65mm, 6 = 75 mm
• On/off safety switch
y
Prevents the tool from being switched on accidentally
- switch on tool by first pressing safety switch and then
pulling trigger switch
-
switch off tool by releasing trigger switch
! after switching off the tool the blade continues to
rotate for a few seconds
• Operating instructions
- hold the mower with both hands
- place the mower on the edge of the lawn and mow in a
forward direction
- reverse at the end of each turn, slightly overlapping the
previous cut strip
! only use the mower on dry grass
- keep the mower away from solid objects and plants
! for mowing long grass, first set the cutting
mechanism to the maximum cutting height, then
to a lower cutting height
! adjust your walking pace when mowing long grass
• Grass box full indicator
u
- empty grass box as soon as flap lowers by itself,
indicating that the grass box is full
- for optimal grass collecting performance regularly clean
the holes underneath flap with a hand brush
• Mulching function
i
- for mulching install mulching plug as shown
• Battery level indicator
w
- press the battery level indicator button to show the
current battery level
w
a
! when the lowest level of the battery indicator
starts flashing after pressing button
w
b, the
battery is empty
! when 2 levels of the battery indicator start flashing
after pressing button
w
c, the battery is not within
the allowable operating temperature range
• Battery protection
The tool is suddenly being switched off or prevented from
being switched on, when
-
the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start flashing when
pressing battery level indicator button
w
c; wait until
battery has returned within the allowable operating
temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level
w
b is shown by the battery level indicator
when pressing battery level indicator button ; charge
battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged