manualshive.com logo in svg

SKC 224-44XR, Руководство по эксплуатации

Поделиться
Скачать
SKC 224-44XR Скачать руководство пользователя страница 2

Form 37711 Rev 1809

Page 2 of 14

www.skcinc.com

Charging Train with single PowerFlex charger

Power 

cable

Charger

Getting Started

Install the Battery Pack

To enhance battery life, SKC ships battery packs separately from the pump. Once installed, completely charge the battery pack before 
operating the pump.

1.  Remove the two screws that secure the battery pack and loosen 

the two case screws above and below the belt clip.

2.  Carefully slide the battery pack out from under the belt clip. 

Ensure that the battery is kept level.

3.  Slip the front edge of the new battery pack under the belt clip 

and position the battery pack to engage the grooves in the case.

4.  Slide the battery pack toward the pump until it is flush with the 

pump case on all sides.

5.  Reinstall two battery screws and tighten the case screws loosened 

in Step 1.

6.  Charge the battery completely. 

See Charge the Battery Pack. 

Note:

 

For optimum charge, ensure the pump is not running during charging.

Charge the Battery Pack

1.  Activate the charger. 

Follow PowerFlex Operating Instructions 37783.

  For optimum charge, ensure that the pump is not running.

2.  Insert the charging cable connector into the charging port on the charger.

3.  Insert the charging plug end of the cable into the jack on the back of the pump’s 

battery pack

 (Figure 1).

4.  Charge the battery completely (the LED at the port connected to the pump is a 

steady green) before using the pump.

5.  Disconnect the charging cable from the back of the pump’s battery pack.

Notes and Cautions

•  To comply with intrinsic safety regulations, do not charge or operate the pump from the charger in hazardous locations.

•  Using a non-approved charger voids any warranty.

•  Using a repaired or rebuilt battery pack voids any warranty and the UL Listing for intrinsic safety.

•  Using any device other than the approved battery pack to power the pump voids the UL Listing for intrinsic safety and any 

warranty.

•  Ensure proper orientation of charging cable before plugging it into the charging jack. Improper orientation/contact will short-circuit 

the battery and voids any warranty.

•  Short-circuiting the battery pack will render it immediately inoperative.

•  Failure to follow warnings and cautions voids any warranty.

•  The battery pack may be kept on the SKC-approved charger for an indefinite time.

For more information on SKC pump battery packs, visit www.skcinc.com/catalog/pdf/instructions/1756.pdf.

Charging 

cable

Back of pump 

with battery pack 

sliding out

Belt clip

Case screw 

(not shown)

Battery pack 

screws

Case screw 

Case grooves

Battery 

connector

Содержание 224-44XR















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды