manualshive.com logo in svg

SKC 224-44MTX, Руководство по эксплуатации

Поделиться
Скачать
SKC 224-44MTX Скачать руководство пользователя страница 27

www.skcltd.com 

224-UMTXM Issue K 

Page 25

Care of the Battery Pack

Battery Testing

1.  Connect SKC approved charger to battery pack. If charger indicator LED illuminates, battery pack charger 

input is ok. If charger LED does not illuminate, battery pack input fuse is blown - Replace battery pack.

2.  Leave battery pack connected to charger to fully charge.
3.  If pump does not function at all after full charge of battery pack, battery pack output fuse has blown, or 

battery cells have failed or are at end of life - Replace battery pack.

4.  If pump functions after full charge of battery pack but gives significantly reduced run times before low 

battery shutdown, battery cells are failing or are at end of life - Replace battery pack.

Battery Replacement 

Refer to pump diagram on page 10. To remove the battery pack unscrew and remove the two battery screws 
(No. 25). Carefully slide the battery pack sideways out from under the metal belt clip (No.22) and remove the 
battery pack.
Fit the replacement battery by sliding it under the metal belt clip. Take care to ensure that the pins of the pump 
power connector engage into the holes in the socket connector on the battery pack. Secure the battery pack 
with the two screws. Do not apply excessive force when tightening the screws. Charge the new battery pack 
fully before use.

Battery Disposal

• 

The EC Battery Directive and equivalent legislation in other countries requires that all batteries and battery 
packs are disposed of correctly at the end of their working life. This means that they must be collected and 
treated separately from other waste.

• 

Please ensure that any end-of-life SKC battery packs are collected and recycled or disposed of correctly.

Содержание 224-44MTX









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды