331 Ushers Road • Ballston Lake, NY 12019 • USA • T +1 518 877 5173 • F +1 518 877 8346 • [email protected]
www.sixnet.com
QUICK START GUIDE
EnterprisePro
TM
Router
GSM R-1300-G or R-3300-G
UNPACKING INSTRUCTIONS
1
Unpack the Sixnet Wireless unit and verify the following
components are enclosed for the EnterprisePro
TM
Router
(Figure A).
Figure A
: Package Contents R-1300-G or R-3300-G:
Not Shown: Antenna included with model R-1300 or R-3300
* Non-US
power supplies require customer-supplied power cord to connect power to
AC power outlet
2
If any items are missing, please contact Sixnet Wireless at
+1 800 489 7781.
3
Optional item to use for Out-of-Band (OOB) Management
function of the Sixnet Wireless modem: Cisco DB9 to RJ45
Console Cable.
GSM MODELS R-1300-G & R-3300-G
1
In most situations, the R-1300 or R-3300 will arrive with the
SIM card installed. If not, open the case…
2
Insert the SIM supplied by your carrier into the SIM socket.
Be sure the SIM is securely fastened by pushing the metal
slide outward to the lock position
.
Replace
the
cover
and
attached
the
antenna.
Note: The notch on the SIM card should be on the bottom right hand side of the
SIM socket.
3
Attach power supply connector to the “barrel” power outlet on
the back of the unit and connect power supply plug to an AC
power outlet.
4
Verify the POWER (green) LED is lit to indicate that the unit is
receiving power.
5
Please allow 2-4 minutes for the unit to connect to the cellular
network. When this has occurred the Signal Strength LEDs
should light up from 1 to 4 LEDs. Sixnet Wireless recommends
2 bars or greater for proper functionality of the unit. If signal
strength is showing 1 LED or showing the top and bottom
LEDs (1 and 4 positions), please refer to the User Manual at
www.sixnet.com
.
Ethernet Cable
(6’ CAT 5E 568B)
Power Supply
(United States)
Power Supply*
(International)
6
Connect to the Ethernet RJ45 port for network connectivity.
ACCESSSING THE GRAPHICAL USER INTERFACE (GUI)
1
Connect PC to EnterpriseProTM Router
The Ethernet Port on the EnterprisePro
TM
Router is “auto-
sensing”, which means a straight through or cross-over cable
can be used to connect to the Sixnet router.
Connect a CAT-5 Ethernet cable between the local PC and the
unit’s Ethernet port. Verify the link LED is lit.
2
Setup PC IP Address for DCHP
For assistance with configuring your PC, see the appropriate
Microsoft Windows support webpage listed at:
http://support.microsoft.com
.
PC to Ethernet Interfaces
Select “Use the following IP address” and fill in the blank fields
with the information below:
Ethernet 0
Ethernet 1
IP address
192.168.0.2 192.168.1.2
Subnet mask
255.255.255.0 255.255.255.0
Default gateway
192.168.0.1 192.168.1.1
Preferred DNS
192.168.0.1 192.168.1.1
3
Access Graphical User Interface
Open a web browser & enter the following in the
address bar:
Ethernet 0:
http://192.168.0.1:10000/
Closed
Open
Ethernet 1
:
http://192.168.1.1:10000/
LOGIN INSTRUCTIONS
• User Name enter:
admin
(lowercase letters)
• For Password enter:
six digit serial number of unit
(lowercase)
Upon successfully logging in you will see the following screen
(Figure B on reverse side)
