Document NO.:
GS
559A-39-001
Version: F
- 4 -
1: Make sure that the host controller (to buy) can work
properly before set up a network, Make sure to set up a
network between alarm and host within an effective
distance.
2: Set the host into learning mode (Refer to the host user
manual).
3: Quickly press the test button for 3 times ,
The LED will
light up and alarm enters" Learning mode ",
when hear a
“beep”, LED off, it means learning is done, alarm is paired
to the host.
4: If pairing failed, the alarm will automatically exit
learning mode after 10 seconds.
(C):
The connection of this product with other
types of alarm
Note:
Other types of alarms must be purchased from
SiterWell such as vibration alarm, Flash alarm, etc. Mainly
applicable to hearing disabled people. After networking
，
When a smoke or temperature alarm occurs, the product
will send an alarm signal to the vibration alarm and flash
alarm.
1: Quickly press the test button for 3 times,
the LED will
light up and alarm enters " Learning mode ".
2: Power on the other types of alarm, then quickly press the
test button for 3 times,
The LED will light up and alarm
enters " Learning mode ". Issued beep, LED off,
Networking success.
(
D): Clear code mode
Firstly press and hold the test button, then power on the
alarm and the LED lights up. Do not release the button until
the LED is off. Press the button again when the LED lights
up second times. if you hear the sound of ‘BI’, it indicates
that clearing is successful. the alarm will reset and get a
new random code.
Maintenance and Cleaning:
In addition to weekly testing, the alarm requires periodic
cleaning to remove dust, dirt, and debris. Clean the alarm at
least once a year to remove dust, dirt, or debris. Use a
vacuum cleaner with a soft brush, vacuum all sides and
covers of smoke alarm. This alarm has a low battery monitor
which will cause the alarm to “chirp” approx every 50
seconds and the red LED flashes once at the same time for a
minimum of 7 days when the battery gets low. If there is a
defective battery or other failures, you can refer to “Trouble
shooting” for solution, if there are still failures during
warranty, you can return to your retailer.
IMPORTANT:
Do not attempt to remove the cover to clean
inside. This will void the warranty.
Repair:
Caution: Do not attempt to repair the alarm. It will affect
your warranty.
If the alarm is not operating properly, and is still under
warranty, return it to the original place you buy. Pack it in a
well-padded carton, and ship to the original place you buy.
If the alarm is no longer under warranty, have a licensed
electrician replace it immediately with a comparable alarm.
Trouble shooting:
DO NOT disconnect battery to quiet an unwanted alarm. This
will remove your protection. Fan the air or open a window to
remove smoke or dust.
Problem
Cause and Remedy
Smoke alarm does not
sound when tested.
1.Clean smoke alarm. Please refer to
the “maintenance and cleaning”
section.
2.If problems persist and the unit is
still under warranty, you can return to
your retailer.
3. If the unit is out of warranty
，
please
replace another new alarm.
Smoke alarm beeps
with the red LED
flashing about once
50
seconds.
The battery is depleted, please replace
the battery
Smoke alarm chirp
occurs every 50
seconds
（
alarm goes
into fault mode
）
.
Clean smoke alarm. Please refer to the
“maintenance and cleaning” section.
Replace the alarm if the problem
persists
Smoke alarm sounds
unwanted alarms
intermittently or when
residents are cooking,
taking showers, etc.
1. Press test button to silence alarm.
2. Clean smoke alarm. Please refer to
the “maintenance and cleaning”
section.
3. Move smoke alarm to new location
and press test button.
The alarm sounds
different from it is
used to. It starts and
stops.
1. Clean smoke alarm. Please refer to
the “maintenance and cleaning”
section.
2. If the problem persists during
warranty, you can return to your
retailer.
3. if the unit is out of warranty
please replace another new alarm.
