Sitecom WL-308 Скачать руководство пользователя страница 69

Страница: 69 / 73

WL-308 Gaming Router

Full Manual

Appendix A – Specifications

Hardware Summary

Physical
Interface

WAN: One 10/100/1000 Gigabit RJ-45

LAN: Four 10/100/1000 Gigabit RJ-45

Reset Button (1 second for Reboot, 5 second for
Reset to Factory Default )

Power Jack

JTAG (for debug only)

LED Status

Power/ Status

WAN (Internet connection)

LAN1~LAN4 (10/100/1000Mbps)

WLAN (Wireless Connection)

Power
Requirements

Power Supply: 90 to 240 VDC ± 10

％

(depends on

different countries)

Device: 12 V/ 1.25A

Radio Specifications

Frequency Band

2.400

～

2.484 GHz

Media Access
Protocol

Carrier sense multiple access with collision avoidance
(CSMA/CA)

Modulation
Technology

OFDM: BPSK, QPSK, 16-QAM, 64-QAM

DBPSK, DQPSK, CCK

Operating
Channels

11 for North America, 14 for Japan, 13 for Europe

Receive
Sensitivity
(Typical)

2.412~2.472G(IEEE802.11b) (1Rx)

-93dBm @ 1Mbps

-91dBm @ 11Mbps

2.412~2.472G(IEEE802.11g) (2Rx)

-92dBm @ 6Mbps

-79dBm @ 54Mbps

2.412~2.472G(IEEE802.11N) (2Rx)

-90 dBm MCS 8

-70 dBm MCS 15

Available transmit
power

2.412~2.472G(IEEE802.11b)

19dBm @1~11Mbps

2.412~2.472G(IEEE802.11g)

Содержание WL-308










































































Результаты поиска

Содержание WL-308

Отзывы:

Sitecom WL-308, Руководство пользователя, Страница: 69 / 73

Результаты поиска

Содержание WL-308

Отзывы: