background image

 

11 / 17 

6.6. Bridged Mono Mode Connections 

 

 

 
 

7.  LX Clip Limitting 

At the amplifier’s full power limit, or clipping point, LX will be activated. This is indicated by an 

illumination of the Limiter LED. The channel gain is automatically reduced, protecting the 

loudspeakers from potential damage from the high power, continuous square waves that would 

otherwise be produced. LX may be activated by uncontrolled feedback, oscillations, improper 

equipment gain settings, or an equipment malfunction upstream from the amplifier. Only steady or 

excessive clipping (not normal program transients) will trigger LX. The circuit is virtually transparent in 

operation and full signal bandwidth is maintained. 

 

8.  IGM Impedance Sensing 

IGM (Instantaneous Gain Modulation) is an innovative circuit that allows the amplifier to operate safley 

into difficult loads. When the amplifier sees a load that overstress the output stage, the IGM circuit 

adjusts the channel gain to a safe level. Like LX, the IGM circuit is inaudible in normal use. In addition, 

if extreme and sustained low impedance is encountered, the amplifier’s output relay will open. 

 

9.  Auto Ramp Protection 

Auto Ramp operates every time the amplifier is turned on or is reactivated after a protect condition is 

corrected. This exclusive feature gradually increases gain to the attenuator setting avoiding 

unnecessary stress on the loudspeakers. 

 

10. 

Thermal Protection 

Abnormally high heat sink temperatures will engage the protect circuit for the overheating channel 

only. (An output relay disconnects the loudspeakers until nominal temperature range is restored.) 

During this time, the Protect LED will light and the LCD display will show Protection and Fault if the 

power transformer gets too hot, its thermal sensing circuit will disconnect both channel outputs. During 

this time, the Active LED will extinguish, the Protect and Limiter LEDs will stay lit and the cooling fan 

will continue running at low speed. Normal operation resumes once the transformer cools to a safe 

level. 

Содержание ELXA Series


















Отзывы: