background image

7 Consumables and spare parts

Sirona Dental Systems GmbH

Gebrauchsanweisung und Installation

108

64 08 137 D3610

D3610.201.02.09.02    11.2017

7

Consumables and spare parts

Hygienic protective sleeves for sensors

Hygienic protective sleeves for sensor size 0 and 1, quantity 300
REF 64 09 960

Hygienic protective sleeve for sensor size 2, quantity 300
REF 64 09 952

Sensor holder tabs

Blue sensor holder tab for front tooth exposure (anterior), quantity 100
REF 61 76 510

Yellow sensor holder tab for side tooth exposures (posterior), quantity
100
REF 61 76 528

Red sensor holder tab for bite wing exposures, quantity 100
REF 61 76 536

Green sensor holder tab for endodontic exposures using half-angle
technique, quantity 100
REF 61 76 544

Gray sensor holder tab for endodontics (measurement exposure),
quantity 50
REF 61 76 551

Sensor holder starter kits

Starter kits include the localizer ring and the guide rod along with 15
sensor holder tabs each for the blue, yellow, red, green and gray sensor
holder. The kit also includes 50 hygienic protective sleeves for one
sensor size.

Sensor holder starter kit for sensor size 0 and 1
REF 64 11 289

Sensor holder starter kit for sensor size 2
REF 64 11 297

Содержание XIOS XG Select

























































































































Отзывы: