Sirona SIROLaser Xtend Скачать руководство пользователя страница 32

Страница: 32 / 78

5 Operation
5.1 Start the device for the first time

Sirona Dental Systems GmbH

Operating Instructions SIROLaser Xtend

63 18 351 D3576

D3576.201.01.05.02 11.2018

Operation

5.1

Start the device for the first time

NOTE

Touch screen functionality: When the touch screen is touched by the
finger the touch field is highlighted. As soon as the finger leaves the
touch screen the action will be started.

Battery state
Information concerning the remaining battery power (only available after
the upgrade)

Connected/charging battery
Battery is connected to power supply and charging (only available after
the upgrade)

Activate Laser
Laser is being activated

Back
User goes back one screen

Home
User goes directly back to home screen

OK
User agrees to settings, confirms and activates action

Save
Settings of application will be saved in My Settings

Delete
Settings of application will be deleted from My Settings

Save as favorite
Application is added to Favorites (only available after the upgrade)

Delete favorite
Application is removed from Favorites (only available after the upgrade)

Peak-pulse
Laser is being set for peak-pulse mode

Continuous wave
Laser is being set for continuous wave mode

Содержание SIROLaser Xtend















































































Результаты поиска

Содержание SIROLaser Xtend

Отзывы:

Похожие инструкции для SIROLaser Xtend

Бренды по названию

Популярные бренды

Sirona SIROLaser Xtend, Руководство по эксплуатации

Результаты поиска

Содержание SIROLaser Xtend

Отзывы:

Похожие инструкции для SIROLaser Xtend

Бренды по названию

Популярные бренды