16
9.1.3 - Sealing – procedure
The machine is ready only if the display shows the “READY” mode.
(
Fig. n°26
)
1. Verify that the film reel is correctly in-
serted
(read par. 8.1).
2. Insert the tray on the appropriate slot
and, then, load the product to seal in-
side the tray requiring sealing (
Fig. n°
28
).
ATTENTION: top plate very hot!
-
The sealer displays the status of the
machine (
a
), the time for the sealing
of the tray (
d
), the preset temperature
(
b
), the current temperature of the
welding plate (e) and the number of
cycles (
c
)
(Fig.n°25)
.
-
In the “
STOP
” mode, press the
“MENU” key
(ref. 3 fig.n°23)
to modify
the time, press it again to modify the
temperature. Use the UP (
ref. 6 fig. n°
23
) and DOWN (
rif. 5 fig. n°23
)
buttons to modify the parameters.
-
To reset the number of cycles, press
twice the “UP” button (
rif.6 fig. n°23
),
resetting can be carried out only in
the "
STOP
” mode.
-
Pressing the “ON/OFF” button (
rif. 2
fig. n°21),
the sealer turns on, the
machine status wil pass from "
WAIT
”,
it will start to heat up the welding
plate until it reaching the set
temperature (
Fig. n°26
).
-
Once the temperature is reached, the
machine is ready to seal with the set
configurations (
Fig. n°27
). The
machine status will read "
READY
”.
Fig. n°27
Fig. n°28
READY 4.0 175°
0001
a
c
STOP 4.0 175°
0001 105°
Fig. n° 25
b
e
d
WAIT 4.0 175°
0001 130°
Fig. n°26
READY 4.0 175°
0001
5
1.1 - PURPOSE
-
The purpose of the Manual consists in providing the instructions as well as the
information, to scrupulously follow for a correct use of the machine and for the
protection and safety of the operator, who must interact with it. The Manual
describes the use of the machine, as provided by the project as well as the
technical features of the machine, provides for instructions on how to move it,
for an appropriate and safe installation, assembly, adjustment and use; it pro-
vides for information relating to the maintenance interventions as well as the
information required to order the spare parts. The Manual clearly shows the
uses, which are not allowed, of the machine, highlighting the residual risks,
with indication of the safety prescriptions to control them.
1.2 - USERS
The Manual is intended to be used by professional and suitably trained person-
nel and, specifically by:
-
Machine operators
-
Maintenance engineers
-
Electrical maintainers
1.3 - USE AND PRESERVATION
-
Each machine model is sold with its own Instruction Manual. The manual forms
an integral part of the machine and it must be preserved in good condition until
the machine is dismantled.
-
THE MANUAL MUST BE PRESERVED IN A SAFE, DRY PLACE, PRO-
TECTED AGAINST DIRECT SUNLIGHT AND IT MUST ALWAYS BE AVAIL-
ABLE FOR CONSULTATION, IN PROXIMITY TO THE MACHINE.
-
In case of transfer of the machine, the Manual must be conveyed to the new
owner.
1.4 - MANAGEMENT AND RESPONSIBILITY
This Manual represents the current status of the machine’s technique and can-
not be considered inappropriate in case of updates of the model, occurred after
the issue of the same Manual. The Manufacturer reserves the right to update
products and manuals, with no obligation to update manuals and previous pro-
duction. The Manufacturer shall hold the rights of intellectual property of this
Manual and it shall forbid its integral and partial disclosure, in any form (print,
copies, microfilms, or other means), as well as the processing, reproduction or
dissemination by electronic systems, towards private individuals or corpora-
tions without its approval. The User is responsible for the management of the
Manual for the entire machine life and will provide for its destruction only upon
disposal of the same machine. Any requests for further copies of this document
must be regularised with a purchase order sent to the Manufacturer.
CHAP. 1 – THE MANUAL
