Sirius Satellite Radio SU-DD2-L INOX, Инструкция по установке, использованию и обслуживанию

Страница: 7 / 20

EN
Before carrying out the appliance installation,
please check that all components are not da-
maged, in such a case contact your retailer
and do not carry out any installation operation.
Furthermore, please read carefully all of the
following installation instructions.
● Use an air exhausting pipe whose maximum
length does not exceed 5 meters.
● Limit the number of elbows in the piping,
since each elbow reduces the air capacity of
1 linear meter. (Ex. : if you use no. 2 x 90 °
elbows, the length of piping should not exceed
3 meters).
● Avoid abrupt direction changes.,
● Use a 5”29/32. constant diameter pipe for
the whole length.(for SUM1 or motor on bo-
ard). Use a 7” 7/8 constant diameter pipe for
the whole length.(for SUM6).
● Use piping approved by standards in force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
Before making the hole, check that there are
no structural or other parts inside the cabinet,
where the appliance is to be placed, which
could hinder a proper installation.
Check that the dimensions of the Downdraft
and the ones of the cook top are compatible
with the cabinet so that the installation can be
carried out properly.
Make a rectangular opening, 3” 15/16 X 19”
9/32 in size, in the back of the cook top for
the SU-DD2L 22” 1/16 model, 3” 15/16 x 31”
3/32 for the SU-DD2L 33” 27/32 model and 4”
6/64 x 19” 9/32 in size, in the back of the cook
top for the SU-DD3 model and 1142 x100 mm
for the 120 cm model. In the version with the
motor already installed, remove the screws
and the suc- tioning unit in order to insert the
down-draft in the hole made.
INSTALLING THE
COOKER HOOD
1.
2.
3.
Put the Downdraft in the opening, inserting it
from above as shown in (Fig. 2).
Fix the downdraft inside the cabinet, using the
special fixing brackets supplied with the pro-
duct (Fig. 3).
Insert the brackets in the lower side of the
downdraft (Fig. 3), in such a way that there
is a 2 mm distance between the lower side of
bracket and the bottom of the cabinet (Fig. 3).
This distance will allow the traction to be po-
sitioned downwards of the product, at the mo-
ment of fixing, in order to have the stain- less
steel trim perfectly adhering with the work
surface. Before inserting the screws, please
make sure that the appliance is per- fectly per-
pendicular with the work surface.
Place the metal box containing the electronic
components in an easily reachable area for
possible technical assistance operations.
by connecting the related connectors (fig. 5).
Once the installation is complete and after
connecting the appliance to the mains pow-
er, lift up the downdraft and remove the door
block (Fig. 4); then open the door (Fig. 5) and
fit the filters in place (Fig. 6). In the ver- sion
of the Downdraft equipped with internal motor,
install the power unit orienting the air outlet to
the desired position, either down- wards or up-
wards (Fig. 7).
The motor can be installed either on the front
or rear side of the downdraft After having in-
stalled the motor, connect the air ducts.
For versions with external motor, place the
suctioning unit (external motor) in a suitable
area and fit the exhaust air flue as illustrated.
Then fit the air outlet ducts between the ex-
ternal motor and the downdraft. Select an air
outlet from the five possibilities (Fig. 9) and fit
the union supplied with the appliance.
Place the metal box with the electronic com-
ponents in an easily reachable area for even-
tual technical assistance operations. (Fig. 9),
connecting the three connectors: 9 pole con-
nector for the actuator control and the safety,
4 pole connector for led lamp (only for SU-
DD2 model) and push-button connector) (Fig.
10). Connect the internal motor or the external
motor’s cable to the 6 poles connector of the
downdraft wiring.
4.
5.
6.
7.
8.
7 SUDD2L - SUDD3