background image

 

1 2  3  4  5 

 

 

 

 

 

 

 

 

 

Safety Instructions 

 

 

20 

 

IN

finity 

510

 

User’s Guide, P1.04 

 

Safety Instructions 

 

Power Disconnect Device 

The plug on the power supply cord is intended to be the power disconnect 
device. As a result, the power source (socket or outlet) shall be located near 
the equipment and shall be easily accessible. 

 

 

 

WARNING: 

FCC Radiation Exposure Statement. The antennas used for this transmitter 

must be installed to provide a separation distance of at least 20 cm from all 

persons and must not be co-located or operating in conjunction with any other 

antenna or transmitter. 

 

 

Caution: 

The INfinity 510 UHF Reader is equipped with four (4) RF ports. To prevent 

reader damage, active RF ports must be properly terminated with a 50 ohm 

load or a functional UHF antenna before power up. UHF Readers are factory 

configured to operate on RF port 1. As a result, port 1 must be properly 

terminated before initially powering on the reader. Before activating any 

additional RF ports, they must also be properly terminated. Never power up 

the reader unless the appropriate loads or antennas are connected. Always 

power down the reader before removing an antenna or load from an RF port. 
The maximum antenna cable length is 10 meters. 

 

 

Caution: Risk 

of 

Explosion

Only replace battery with same type and designation. 

There is risk of explosion if battery is replaced with incorrect type. Dispose of 

old battery according to manufacturer’s instructions and local regulations. 

 

 

 

 

 

Содержание INfinity 510























Отзывы: