sirea MicroARM-A9 Скачать руководство пользователя страница 10

MicroARM-A9

Programmable Logic Controller

  

Observe the following pictograms:

Attention.
On the product label this symbol means that the notice must be consulted.
In this manual, this symbol indicates important information.

Direct current.

Alternating current.

This device is CE approved and complies with the national and European 
guidelines. 

8. Protection device

Quick fuse protections must be positioned on the 24 volt continuous start feeding the
PLC. These fuses will be sized according to the number of devices set in series behind the
start.

9. Elimination

Old electronic devices are recyclables goods that should not be thrown into the
trash   can.   If   the   device   reaches   the   end   of   its   life,   it   should   be   eliminated   in
accordance   with   the   legal   regulations   in   force   to   the   recovery   centres   in   your
municipality. Elimination in the household trashes is prohibited.

10. Cleaning

For cleaning, use a clean, dry, antistatic, lint-free cloth without corrosive products.

11. Technical features

Power supply

9 to 36 V

or 110 to 230 V  

Maximum operating Altitude

2000 m

Maximum operating Temperature

45 °celsius

Maximum Operating Humidity

70 %

10

Содержание MicroARM-A9











Отзывы: