background image

 

 

Sipura SPA-2002 Configuration Guide

 

 

Page 4 

 

3. Configuration 

3.1  Configuration for Outbound Calling 

To configure the SPA-2002 for outbound calling: 

1.  Connect to the SPA-2002 by entering the device’s IP address in the Web 

browser’s Address bar.  For instructions on obtaining the IP address, refer to 
section 2.0 Accessing the SPA-2002 in Section 2.0 of this Guide. 

2.  Click on the Admin Login link in the upper right corner of the page, and then 

click the advanced configuration link. 

 

SPA-2002 Web Interface – Main Window

 

3. Click 

the 

Line1 or Line2 tab at the top of the page, and in the NAT Settings 

section, change the following setting: 

Field 

Value 

NAT Keep Alive Enable 

no 

4. In 

the 

Proxy and Registration section (see the screen on the following page), 

change the following settings: 

Field 

Value 

Proxy 

byod1.net2phone.com 

Use Outbound Proxy 

no 

Use OB Proxy In Dialog 

no 

Make Call Without Reg 

yes 

Ans Call Without Reg 

yes 

DNS SRV Auto Prefix 

no 

5. In 

the 

Subscriber Information section (as shown in the Line1/2 Window screen on 

the following page), enter a Display Name.  Enter the following values for 

outbound only service: 

Service Type 

Field 

Display Name 

Value 

Display Name (Line 1) 

NO_DID1 

OUTBOUND SERVICE ONLY 

Display Name (Line 2) 

NO_DID2 

6. Enter 

the 

User ID (account) and Password (PIN). 

Содержание SPA-2002











Отзывы:

Похожие инструкции для SPA-2002