6
SAFETY INSTRUCTIONS….cont
and safest performance. Follow instructions for lubricating and changing accessories.
All extension cables must be checked at regular intervals and replaced if damaged.
Always keep the vice hand-wheel grip/s on the circular saw clean, dry and free of oil
and grease.
USE ONLY RECOMMENDED ACCESSORIES:
Consult this user manual, your distributor or
SIP directly for recommended accessories. Follow the instructions that accompany the
accessories. The use of improper accessories may cause hazards and will invalidate
any warranty you may have.
REMOVE ADJUSTING KEYS AND WRENCHES:
Form a habit of checking to see that keys
and adjusting wrenches are removed from the circular saw before every use.
SECURE THE WORK-PIECE:
Always use the vice to hold the work-piece. This frees up
both hands to operate the circular saw.
DO NOT OVERREACH:
Keep proper footing and balance at all times.
USE THE RIGHT TOOL:
Do not use the circular saw to do a job for which it was not de-
signed.
DO NOT FORCE THE CIRCULAR SAW:
It will do the job better and more safely at the rate
which it was designed.
DO NOT OPERATE THE CIRCULAR SAW IN EXPLOSIVE ATMOSPHERES:
Do not use the cir-
cular saw in the presence of flammable liquids, gases, dust or other combustible
sources. Circular sawing operations may create sparks which can ignite the dust or
fumes.
DO NOT EXPOSE THE CIRCULAR SAW TO RAIN OR USE IT IN WET CONDITIONS:
Water en-
tering circular saw will greatly increase the risk of electric shock.
HAVE YOUR CIRCULAR SAW REPAIRED BY A QUALIFIED PERSON:
The tool is in accord-
ance with the relevant safety requirements. Repairs should only be carried out by
qualified persons using original spare parts, otherwise this may result in considerable
danger to the user.
DO NOT
dismantle, tamper with or use the circular saw without all guards fitted as this
may be dangerous and will invalidate the warranty.
Keep hands out of the path of the circular saw blade, never reach around cir-
cular saw blade.
Make sure the circular saw blade is clear of the work-piece before the handle
trigger is pressed in.
Stop operation immediately if you notice anything abnormal.
Wait for the circular saw blade to stop completely and remove the plug from
mains supply before servicing or adjusting the circular saw or changing the
blade.
Be alert at all times, especially during repetitive, monotonous operations. Don't
be lulled into a false sense of security. Circular saw blades can be extremely
unforgiving.
31
PARTS LIST
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
102.
Cover
WK03-00100
305.
Bolt
WK03-00120
103.
Pump support
WK03-00101
306.
Rubber cover
WK03-00121
104.
Bolt M6x12
WK04-00038
307.
Pipe clamp
WK03-00122
105.
Spring washer M6
WK03-00102
308.
Nut
WK03-00123
106.
Bolt M10x100
WK03-00103
320.
Pin
WK03-00124
107.
Bolt M6x12
WK04-00038
321.
Mitre handle knob
WK03-00125
108.
Spring washer M6
WK03-00102
322.
Mitre handle
WK03-00126
109.
Electrical label
WK03-00104
323.
Shaft
WK03-00127
110.
General label
WK03-00105
324.
Nut
WK03-00128
111.
Coolant pump
WK04-00313
325.
Tensioning nut
WK03-00129
112.
Coolant tank filter
WK03-00106
326.
Nut
WK03-00130
113.
Bolt M6x12
WK04-00038
327.
Bolt
WK03-00131
114.
Coolant tank
WK04-00020
328.
Pressure plate
WK03-00132
201.
Angle scale
WK03-00107
337.
Front vice jaw left
WK03-00133
202.
Rivet
WK03-00108
N/A
Rear vice jaw right
WK03-00133
203.
Spring
WK03-00109
338.
Front vice jaw right
WK03-00134
204.
Washer M10
WK04-00046
N/A.
Rear vice jaw left
WK03-00134
205.
Bolt M10x100
WK03-00103
339.
Front vice jaw holder
WK03-00135
206.
Nut M10
WK04-00052
340.
Cap head bolt
WK03-00136
207.
Base mesh filter
WK03-00110
341.
Vice handle
WK03-00137
208.
Spring fixed plate
WK03-00111
342.
Vice handle knob
WK03-00138
209.
Spring fixed plate
WK03-00112
343.
Plastic cover
WK03-00139
210.
Washer
WK03-00113
344.
Handle boss
WK03-00140
220.
Base
WK03-00114
345.
Guide shaft
WK03-00141
221.
Swivel base
WK03-00115
346.
Vice base
WK03-00142
222.
Grease nipple
WK03-00116
347.
Cap head bolt
WK03-00143
223.
Swivel base shaft
WK03-00117
349.
Rear vice jaw holder
WK03-00144
302.
Nut M10
WK04-00052
350.
Support block
WK03-00145
303.
Ring
WK03-00118
351.
Cap head bolt
WK03-00146
304.
Plate
WK03-00119
353.
Vice shaft
WK03-00147
305.
Bolt
WK03-00120
401.
Ring
WK03-00148
