The thermostat features two temperature
regulation modes:
A mode (default):
Regulation of ambient temperature
with the possibility to limit floor temperature through an external
temperature sensor.
F mode:
Regulation of floor temperature through an
external temperature sensor with the possibility to limit
ambient temperature.
11) Circulator pump's anti-seizure
When the thermostat is not heating for an extended period, this
parameter will activate the main output during 1 minute every
24 hours to ensure the hydronic system pump does not seize.
TECHNICAL SPECIFICATIONS
Operating voltage:
24 Vac
Maximum load:
1 Amp
Setpoint range:
5 ˚C to 36 ˚C (41 ˚F to 97 ˚F)
Display range:
0 ˚C to 70 ˚C (32 ˚F to 99 ˚F)
Resolution:
±
0,5 ˚C (
±
1 ˚F)
Storage:
-20 ˚C to 50 ˚C (-4 ˚F to 122 ˚F)
Auxiliary output:
24 Vac / Vdc / 0.1 A
Protocol:
Zigbee 3.0
Frequency:
2.4 GHz
Transmission power:
+20 dBm
Receiver sensitivity:
-108 dBm
Compatible with:
• Baseboard heater activated by mechanical relay
or electonic relay (SSR)
• Fan-forced convector activated by mechanical relay
or electronic relay (SSR)
• Electric floor heating (activated by a relay)
• Hydronic floor heating
• Hydronic heating system
• Furnace (without fan control)
All of the thermostat's parameters can be set through your
compatible Zigbee hub. However, if you have not
connected your thermostat to your Zigbee network
and wish to change the temperature format or the control
cycle, you need to:
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
of the device.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty,
will be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
For more information, visit our Website:
660-0735-0020-E
PARAMETERS THAT CAN BE CONTROLLED
FROM THE DEVICE (CONTINUED):
USER SETTINGS
PARAMETERS THAT CAN BE CONTROLLED FROM
THE DEVICE (CONTINUED):
Lower the setpoint to its minimum and hold the button for
10 seconds to access the menu.
Press the or the button to change the setting.
Press the and the buttons simultaneously to save and go
to the next parameter. Continue to press until the end of the list
to exit the menu.
0.15
5
10
15
20
25 30
Convector or baseboard heater
activated by electronic relay (SSR)
Minimum cycle length (min)
Fan-forced convector activated
by electronic relay (SSR)
Fan-forced convector or
baseboard heater activated by
mechanical relay
Hydronic heating pump system
Furnace
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons simultaneously
for 10 seconds. The symbol will disappear from the display.
DISCONNECT YOUR THERMOSTAT FROMT THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
Neviweb® is a registered trademark of Sinopé Technologies Inc. in Canada and the United States.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
Google Play and the Google Play logo are trademarks of Google Inc.
Alimentez le thermostat.
10 sec.
10 sec.
Alimentez le thermostat.
8) and 9) Main and auxiliary output cycle length
The thermostat has a main and an auxiliary output.
Select the appropriate cycle length based on your heating
system. The selection of an inappropriate cycle length may
damage your unit.
7) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in
order to keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is
connected to the thermostat.
6) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to
ensure it does not exceed the selected limit. This parameter is
ideal for protecting engineered wood floors. (Verify with your
flooring manufacturer to determine the heat limit.)
This parameter is only usable when a floor sensor is connected
to the thermostat.
5) Maximum limit of the ambient
temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit.
#
Parameters & settings
Display
8
Name
Aux
Cyc
9
Cyc
6
Max
Floor
Max
Air
10
Sens
11
PE
Maximum floor temperature limit
(Only visible in A mode)
7 °C to 36 °C – (Default: OFF)
7
Min
Floor
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C - (Default OFF)
Floor sensor
10K or 12K – (Default: 10K)
Circulator pump's anti-seizure
ON or OFF (Default: OFF)
#
Parameters & settings
Display
2
Name
Control
1
Temp
Temperature format
°C or °F – (Default: °C)
Control mode of thermostat
A (Air), F (Floor) – (Default: A)
4
Max
3
Min
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
5
Maximum ambient temperature limit
(Only visible in F mode)
5 °C to 36 °C - (Default OFF)
Cycle lenght / Main output
15 sec, 5 min, 10 min, 15 min, 20 min,
25 min, 30 min – (Default: 15 min)
Cycle lenght / Auxiliary output
OFF, 15 sec, 5 min, 10 min, 15 min, 20 min,
25 min, 30 min – (Default: OFF)
PARAMETERS THAT CAN BE CONTROLLED
FROM THE DEVICE :